PV36Y103C01B00 Murata, PV36Y103C01B00 Datasheet - Page 76

• Manufacturer Part Number: PV36Y103C01B00
• Description: Trimmer Resistors - Multi Turn 10Kohms 10mm Square 25turn
• Manufacturer: Murata

Specifications of PV36Y103C01B00

• Resistance: 10 KOhms
• Power Rating: 0.5 Watt (1/2 Watt)
• Operating Temperature Range: - 55 C to + 125 C
• Element Type: Cermet
• Product: Multi-Turn Trimmer Potentiometers
• Tolerance: 10 %
• Number Of Turns: 25
• Taper: Linear
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

!Note
!Note
1. Store in temperatures of -10 to +40deg. C and
2. Do not store in or near corrosive gases.
3. Use within six months after delivery.
4. Open the package just before using.
5. Do not store under direct sunlight.
6. Do not use the rotary position sensor under the
1. Soldering
1. Soldering
(1) PVS1A series can be soldered by reflow soldering
(2) The dimension of land pattern used should be
(3) Standard soldering condition
(1) PVS1L series can be soldered by flow soldering
(2) Standard soldering condition
Notice (Operating and Storage Conditions)
relative humidity of 30-85%RH.
following environmental conditions. If you use
the rotary position sensor in an environment other
these listed below, please consult with Murata
factory representative prior to using.
Notice (Soldering and Mounting)-PVS1A Type
Notice (Soldering and Mounting)-PVS1L Type
method and soldering iron. Do not use flow
soldering method (dipping).
Murata's standard land pattern at reflow
soldering. Excessive land area may cause
displacement due to the effect of the surface
tension of the solder. Insufficient land area
may cause insufficient soldering strength on PCB.
(a) Reflow soldering : Refer to the standard
(b) Soldering iron:
method and soldering iron. Do not use reflow
soldering method.
(a) Flow soldering
(b) Soldering iron
Before using other soldering conditions than
those listed above, please consult with Murata
factory representative prior to using. If the
Before using other soldering conditions than
those listed above, please consult with Murata
factory representative prior to using. If the
• Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this PDF catalog to prevent smoking and/or burning, etc.
This catalog has only typical specifications. Therefore, you are requested to approve our product specifications or to transact the approval sheet for product specifications before ordering.
>Temperature of tip 360 deg. C max.
>Soldering time
>Diameter
>Wattage of iron
>Pre-haeting temp.: 80-100 deg. C
>Soldering temp. : 260 deg. C max.
>Soldering time : 3 sec. max.
>Temperature of tip: 360 deg. C max.
>Soldering time
>Diameter
>Wattage of iron : 30W max.
temperature profile.
: 3mm max.
3mm max.
: 3 sec. max./1 terminal
3 sec. max./1 terminal
30W max.
2. Mounting
3. Cleaning
2. Mounting
(4) The amount of solder is critical. Insufficient
(5) The soldering iron should not come in contact
(1) Do not apply excessive force (preferable 9.8N
(2) Do not warp and/or bend PCB to prevent the rotary
(3) The amount of solder is critical.
(4) The soldering iron should not come in contact
(1) Use PCB hole to meet the pin of the rotary
(2) Do not apply excessive force (preferably 9.8N
(1) Corrosive gasses atmosphere
(2) In liquid
(3) Dusty / dirty atmosphere
(4) Direct sunlight
(5) Static voltage nor electric/magnetic fields
(6) Direct sea breeze
(7) Other variations of the above
Cannot be cleaned because of open construction.
amounts of solder can lead to insufficient
soldering strength on PCB. Excessive amounts of
solder may cause bridging between the
terminals.
with the cover of the rotary position sensor. If
such contact does occur, the rotary position
sensor may be damaged.
(Ref.; 1kgf) max.), when the rotary position
sensor is mounted to the PCB.
position sensor from breakage.
with the cover of the rotary position sensor. If
such contact does occur, the rotary position
sensor may be damaged.
position sensor. If the rotary position sensor
is installed into insufficient PCB hole, the
rotary position sensor may be damaged by
mechanical stress.
(Ref.; 1kgf) max.), when the rotary position
soldering conditions are not suitable, e.g.,
excessive time and/or excessive temperature,
the rotary position sensor may deviate from the
specified characteristics.
soldering conditions are not suitable, e.g.,
excessive time and/or excessive temperature,
the rotary position sensor may deviate from the
specified characteristics.
(Ex. Chlorine gas, Hydrogen sulfide gas, Ammonia
gas, Sulfuric acid gas, Nitric oxide gas, etc.)
(Ex. Water, Oil, Medical liquid, Organic
solvent, etc.)
PVS1 Series Notice
Continued on the following page.
R50E13.pdf 04.6.11
75
9