E6C2-CWZ6C 200P/R 2M Omron, E6C2-CWZ6C 200P/R 2M Datasheet

Page 1

... Description --- Incorporates ends different to each other in diameter Metal construction --- --- Provided with the E69-FCA02 flange 2 E6C2-C Part number E6C2-CWZ6C E6C2-CWZ3E E6C2-CWZ1X E6C2-CWZ5B Part number E69-C06B E69-C68B E69-C06M E69-FCA E69-FCA-02 E69-2 ...

Page 2

... Dielectric strength 500 VAC, 50/60 Hz for 1 min between carry parts and case Note inrush current of approx flows for approx. 0.3 ms right after the E6C2-C is turned on. 2. The line driver output of the E6C2-C is used for data transmission circuitry conforming to RS-422A and ensures long-distance transmission over twisted-pair cable, with quality equivalent to AM26LS31 ...

Page 3

... White: Phase B; NPN main Orange: Phase Z) transistor circuitry 3.3 Ω max Ground E6C2-CWZ5B 5 VDC±5% Non-reversed output (Black: Phase A; White: Phase B; Orange: Phase Z) E6C2-C Reversed output (Black max. main Red: Phase A; White/Red: circuitry Phase B; Orange/Red: Phase Ground PNP transistor 4 E6C2-C E6C2-CWZ1X E6C2-CWZ5B ...

Page 4

... Phase Phase B L 1/4T±1/8T (90°±45°) H Phase Z L Note: Phase A is 1/4±1/8T faster than phase B. J LINE DRIVER OUTPUT E6C2-CWZ1X Direction or resolution: Clockwise (CW) (As viewed from the end of the shaft) T (360° Phase Phase B L 1/4T±1/8T (90°±45°) ...

Page 5

... E6C2-C J OUTPUT PROTECTION CIRCUIT The E6C2-C with open collector or voltage output incorporates a circuit protecting the E6C2-C from damage resulting from load short-circuiting or wiring the output wrong. J ORIGIN INDICATION It is easy to adjust the position of phase Z with the origin indication function. The illustration below on the left side shows the relationship be- tween phase Z and the origin ...

Page 6

... Note: Material: SPCC, t=3.2 Mounting Dimensions 68±0.2 dia. (2.68±0.008) 7 E6C2-C E69-C06M (Metal Construction) 19.1 Four, M3 hexagon 2.4 2.4 set screws (6 +0.022 ) 19.1 dia. - -0.00 Note: Material: Super duralumin ...

Page 7

... Blue Note: 1. The shield is not connected to the internal circuits or casing of the E6C2-C. 2. There is no difference in circuit among phases A, B, and Z. 3. Connect the GND terminal the ground when the E6C2 normal operation. Connection Examples J H7ER SELF-POWERED TACHOMETER Applicable Model: E6C2-CWZ3E (with a resolution of 10 ...

Page 8

... COUNTER UNIT CW and CCW detection (increment/decrement counting) Applicable Model: E6C2-CWZ6C E6C2-C Brown Black Blue White Shielded Internal DIP switch settings J CQM1 PROGRAMMABLE CONTROLLER Applicable Model: E6C2-CWZ6C E63-WF5C CQM1 E6C2-CWZ6C Brown (12 V) Black (Phase A) White (Phase B) Orange (Phase Z) Blue (0 V) Shielded 9 E6C2-C ...

Page 9

... Phase B and power supply A17 and B18 J CQM1-CPU43-EV1 (AS BUILT-IN HIGH-SPEED COUNTER) The pulse output of the E6C2-C can be directly input into IN04, IN05, and IN06 of the CPU Unit to use these three points as a built-in high-speed counter. The single-phase response speed is 5 kHz, and the two-phase response speed is 2 ...

Page 10

... Do not wire power lines or high-tension lines along with the power supply lines of the E6C2-C Rotary Encoder. J MOUNTING • Be careful not to spray water or oil onto the E6C2-C Rotary Encoder. • The E6C2-C Rotary Encoder consists of high-precision components. To avoid malfunction, handle with extreme care and do not drop the Rotary Encoder. • ...

Page 11

... A wrong pulse may be generated when the E6C2-C Rotary Encoder is turned on or off. Do not use the connected device for 0.1 s after the E6C2-C Rotary Encoder is turned on and for 0.1 s before the E6C2-C Rotary Encoder is turned off. Cable Extension • ...

Page 12

... OMRON ELECTRONICS LLC One East Commerce Drive Schaumburg, IL 60173 1-800-55-OMRON Cat. No. CEDSAX4 11/01 OMRON ON- -LINE Global -- http://www.omron.com USA -- http://www.omron.com/oei Canada -- http://www.omron.com/oci Specifications subject to change without notice. E6C2-C OMRON CANADA, INC. 885 Milner Avenue Scarborough, Ontario M1B 5V8 416-286-6465 Printed in U.S.A. ...