PIC16F87-E/P Microchip Technology, PIC16F87-E/P Datasheet - Page 120

• Manufacturer Part Number: PIC16F87-E/P
• Description: IC,MICROCONTROLLER,8-BIT,PIC CPU,CMOS,DIP,18PIN,PLASTIC
• Manufacturer: Microchip Technology
• Series: PIC® 16Fr

Specifications of PIC16F87-E/P

• Rohs Compliant: YES
• Core Processor: PIC
• Core Size: 8-Bit
• Speed: 20MHz
• Connectivity: I²C, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Number Of I /o: 16
• Program Memory Size: 7KB (4K x 14)
• Program Memory Type: FLASH
• Eeprom Size: 256 x 8
• Ram Size: 368 x 8
• Voltage - Supply (vcc/vdd): 4 V ~ 5.5 V
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 125°C
• Package / Case: 18-DIP (0.300", 7.62mm)
• Processor Series: PIC16F
• Core: PIC
• Data Bus Width: 8 bit
• Data Ram Size: 368 B
• Interface Type: SSP, USART
• Maximum Clock Frequency: 20 MHz
• Number Of Programmable I/os: 16
• Number Of Timers: 3
• Operating Supply Voltage: 2 V to 5.5 V
• Maximum Operating Temperature: + 125 C
• Mounting Style: Through Hole
• 3rd Party Development Tools: 52715-96, 52716-328, 52717-734
• Development Tools By Supplier: PG164130, DV164035, DV244005, DV164005, PG164120, ICE2000, DM163014
• Minimum Operating Temperature: - 40 C
• Data Rom Size: 256 B
• Height: 3.3 mm
• Length: 22.86 mm
• Supply Voltage (max): 5.5 V
• Supply Voltage (min): 4 V
• Width: 6.35 mm
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: ACICE0202 - ADAPTER MPLABICE 18P 300 MIL
• Data Converters: -
• Lead Free Status / Rohs Status: Details

PIC16F87/88
12.2
The A/D conversion time per bit is defined as T
A/D conversion requires 9.0 T
The source of the A/D conversion clock is software
selectable. The seven possible options for T
• 2 T
• 4 T
• 8 T
• 16 T
• 32 T
• 64 T
• Internal A/D module RC oscillator (2-6 s)
For correct A/D conversions, the A/D conversion clock
(T
as small as possible, but no less than 1.6 s and not
greater than 6.4 s.
Table 12-1 shows the resultant T
the device operating frequencies and the A/D clock
source selected.
TABLE 12-1:
DS30487C-page 118
Note 1:
AD
) must be selected to ensure a minimum T
OSC
OSC
OSC
OSC
OSC
OSC
2:
3:
Operation
RC
16 T
32 T
64 T
Selecting the A/D Conversion
Clock
2 T
4 T
8 T
The RC source has a typical T
When the device frequencies are greater than 1 MHz, the RC A/D conversion clock source is only
recommended for Sleep operation.
For extended voltage devices (LF), please refer to Section 18.0 “Electrical Characteristics”.
(1,2,3)
OSC
OSC
OSC
OSC
OSC
OSC
T
AD
vs. MAXIMUM DEVICE OPERATING FREQUENCIES – STANDARD DEVICES (C)
AD Clock Source (T
AD
AD
per 10-bit conversion.
ADCS<2>
times derived from
0
1
0
1
0
1
x
AD
AD
time of 4 s, but can vary between 2-6 s.
AD
AD
are:
. The
time
AD
)
ADCS<1:0>
12.3
The selection of the automatic acquisition time and
A/D conversion clock is determined in part by the clock
source and frequency while in a power-managed
mode.
If the A/D is expected to operate while the device is in
a power-managed mode, the ADCS2:ADCS0 bits in
ADCON0 and ADCON1 should be updated in accor-
dance with the power-managed mode clock that will be
used. After the power-managed mode is entered
(either of the power-managed Run modes), an A/D
acquisition or conversion may be started. Once an
acquisition or conversion is started, the device should
continue to be clocked by the same power-managed
mode clock source until the conversion has been
completed.
If the power-managed mode clock frequency is less
than 1 MHz, the A/D RC clock source should be
selected.
00
00
01
01
10
10
11
Operation in Power-Managed
Modes
Maximum Device Frequency
 2005 Microchip Technology Inc.
1.25 MHz
2.5 MHz
(Note 1)
10 MHz
20 MHz
20 MHz
5 MHz
Max.