AS5163-HTST austriamicrosystems, AS5163-HTST Datasheet - Page 12

• Manufacturer Part Number: AS5163-HTST
• Description: IC ENCODER ROTARY 14-TSSOP
• Manufacturer: austriamicrosystems
• Type: Linear, Rotary Encoder - Programmabler

Specifications of AS5163-HTST

• Sensing Range: 30mT ~ 70mT
• Voltage - Supply: 4.5 V ~ 5.5 V
• Current - Supply: 20mA
• Output Type: Analog, Ratiometric
• Operating Temperature: -40°C ~ 150°C
• Package / Case: 14-TSSOP (0.173", 4.40mm Width)
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Current - Output (max): -
• Features: -

AS5163
Datasheet - D e t a i l e d D e s c r i p t i o n
7.2.6 Analog Output Diagnostic Mode
Due to the low pin count in the application, a wrong operation must be indicated by the output pin OUT. This could be realized using the failure
bands. The failure band is defined with a fixed level. The failure band low is specified from 0% to 4% of the supply range. The failure band high
is defined from 100% to 96%. Several failures can happen during operation. The output signal remains in these bands over the specified
operating and load conditions. All the different failures can be grouped into the internal alarms (failures) and the application related failures.
C
R
Table 8. Different Failure Cases of AS5163
For efficient use of diagnostics, it is recommended to program to clamping levels CLL and CLH.
7.2.7 Analog Output Driver Parameters
The output stage is configured in a push-pull output. Therefore it is possible to sink and source currents.
C
R
Table 9. General Parameters for the Output Driver
Note: A Pull-Up/Down load is up to 1kΩ with increased diagnostic bands from 0%-6% and 94%-100%.
www.austriamicrosystems.com/AS5163
LOAD
PD
Internal alarms (failures)
LOAD
PD
ILEAKOUT
= 2k…5.6kΩ load pull-up
= 2k…5.6kΩ load pull-up
Application related
IOUTSCH
IOUTSCL
BGNDPU
BGNDPD
TSCREC
BVDDPU
BVDDPD
TSCDET
Symbol
≤ 42 nF, R
≤ 42 nF, R
failures
Type
PU
PU
Short circuit output current (high side driver)
Short circuit output current (low side driver)
Output voltage broken GND with pull-down
Output voltage broken VDD with pull-down
= 2k…5.6kΩ
= 2k…5.6kΩ
Output voltage broken GND with pull-up
Output voltage broken VDD with pull-up
Out of magnetic range
(too less or too high magnetic
input)
Cordic overflow
Offset compensation finished
Watchdog fail
Oscillator fail
Overvoltage condition
Broken VDD
Broken VSS
Short circuit output
Short circuit detection time
Short circuit recovery time
Output Leakage current
Parameter
Failure Mode
MAGRng
Symbol
Min
Revision 2.7
-20
BVDD
BVSS
20
96
96
-8
WDF
COF
OCF
SCO
8
2
0
0
OV
OF
Typ
Failure Band
High/Low
High/Low
High/Low
High/Low
High/Low
High/Low
High/Low
Max
600
100
100
-32
32
20
20
4
4
%VDD
%VDD
%VDD
%VDD
Unit
mA
mA
ms
µA
µs
Could be switched off by one OTP bit
ALARM_DISABLE.
Programmable by OTP bit DIAG_HIGH
Programmable by OTP bit DIAG_HIGH
Programmable by OTP bit DIAG_HIGH
Programmable by OTP bit DIAG_HIGH
Programmable by OTP bit DIAG_HIGH
Dependant on the load resistor
Pull up → failure band high
Pull down → failure band low
Switch off → short circuit dependent
output stage turned on
output stage turned off
V
R
R
R
R
OUT
PU
PD
PU
PD
Note
V
V
OUT
OUT
= 2k…5.6k
= 2k…5.6k
= 2k…5.6k
= 2k…5.6k
Note
=VDD=5V
=27V
=0V
12 - 36