H3YN-21-200/230AC Omron, H3YN-21-200/230AC Datasheet
H3YN-21-200/230AC
Specifications of H3YN-21-200/230AC
Related parts for H3YN-21-200/230AC
H3YN-21-200/230AC Summary of contents
Page 1
... Ordering Information Supply voltage 24, 100 to 120, 200 to 230 VAC; DPDT 100 to 110 12, 24, 48, 100 to 110, 4PDT 125 VDC 24 VDC 4PDT (Twin contact) Note: Specify both the model number and supply voltage when ordering. Example: H3YN-2 24 VAC Model Number Legend H3YN Output 2: DPDT ...
Page 2
... Control outputs Note: 1. Single-phase, full-wave-rectified power supplies can be used. 2. When using the H3YN continuously in any place where the ambient temperature range supply 90% to 110% of the rated supply voltages (supply 95% to 110% with 12 VDC type). 3. Set the reset voltage as follows to ensure proper resetting. ...
Page 3
... Electrical: DPDT: 500,000 operations min 250 VAC, resistive load at 1,800 operations/h) 4PDT: 200,000 operations min. (H3YN-4-Z/-41-Z: 100,000 operations min 250 VAC, resistive load at 1,800 operations/h) Between power terminals for 100 to 120 VAC, 200 to 230 VAC, 100 to 110 VDC, 125 VDC ...
Page 4
... Maximum current of 0.2 A can be switched if L ms. In both cases, a life of 100,000 operations can be expected. The minimum applicable load is 0 VDC (P reference value). 4 250 VAC, cos = 0.4 5,000 24 VDC, L 1,000 500 200 Load current (A) 250 VAC, cos = 0.4 5,000 24 VDC, L 1,000 500 200 Load current (A) H3YN ...
Page 5
... Time limit contact NC (9-1, 10-2, 11-3, 12-4) Time limit contact NO (9-5, 10-6, 11-7, 12-8) Run/Power indicator (PW) Output indicator (UP) Power (13-14) Time limit contact NC (9-1, 10-2, 11-3, 12-4) Time limit contact NO (9-5, 10-6, 11-7, 12-8) Run/Power indica- tor (PW) Output indicator (UP) H3YN H3YN-4/-41 5 ...
Page 6
... H3YN DIP Switch Settings The 1-s range and ON-delay mode for H3YN-2/-4/-4-Z, the 1-min range and ON-delay mode for H3YN-21/-41/-41-Z are factory-set before shipping. Time Ranges Model Time range Time setting range H3YN- 0 H3YN-4 H3YN-4-Z H3YN-4 min 0 min 10 min ...
Page 7
... H3YN-4/-41 Front Mounting H3YN-4-Z/-41-Z Fourteen, 3 Mounting Height PYF08A/PYF08A-N/PYF08A-E (PYF14A/PYF14A-N/PYF14A-E (see note)) H3YN Series PYF08A (PYF14A) Note: Models in parentheses are Sockets connecting to the H3YN-4/-4-Z. 28 max. 21.5 max 1.2 elliptic holes 28 max. 21.5 max PY08 (PY14 (see note)) H3YN Series PY08 (PY14) ...
Page 8
... H3YN Accessories (Order Separately) Connecting Sockets Use the PYF -02 QN(2) to mount the H3YN. When ordering any one of these Sockets, replace “ ” with “08” or “14.” Track Mounting/Front Connecting Sockets PYF08A Two, 4 mounting holes Eight sems 72 max. 23 max. 16.5 30 max. ...
Page 9
... View) (Top View) Terminal Arrangement Panel Cutout (Bottom View) 25.8 PY08 PY14 Terminal Arrangement (Bottom View) PY08QN PY14QN PY08QN(2) PY14QN(2) Terminal Arrangement (Bottom View) PY08 -02 PY14 -02 H3YN Two, 4.5 dia Two, 4.5 dia +0.2 21.4 0 H3YN Series 59.3 +0 -02, PY QN(2) 9 ...
Page 10
... Sockets to be used. PYP-1 Two, 3.4-dia. holes 1.6 Square hole Hold-down Clips The Hold-down Clip makes it possible to mount the H3YN securely and prevent the H3YN from falling out due to vibration or shock. Y92H-3 Y92H-4 10 PYP-18 492 17 x 27.4 = 465.8 0.6 13.1 27 ...
Page 11
... Connection H3YN-2/-21 DIN Indication Timer circuit UP PW Pulse Operation A pulse output for a certain period can be obtained with a random external input signal. Use the H3YN in interval mode as shown in the following timing charts. H3YN-2/-21 Timer circuit External input H3YN-4/-41 H3YN-4-Z/-41-Z Timer circuit ...
Page 12
... Use the following safety circuit when building a self-holding or self- resetting circuit with the H3YN and an auxiliary relay, such Relay, in combination. In the case of the above circuit, the H3YN will be in pulse operation. Therefore, if the circuit shown on page 11 is used, no auxiliary relay will be required. ...