SP100R BANNER ENGINEERING, SP100R Datasheet - Page 4

• Manufacturer Part Number: SP100R
• Description: PHOTO SENSOR RECEIVER
• Manufacturer: BANNER ENGINEERING

Specifications of SP100R

• Output Current: 150mA
• Sensor Output: NPN Open Collector
• Supply Voltage Range Dc: 10V To 30V
• Leaded Process Compatible: No
• Peak Reflow Compatible (260 C): No

4
Sensors for use with MA3 and MA3P Modulated Amplifiers
Temperature range for all miniature modulated remote sensors is 0 to 70 degrees C (+32 to 158 degrees F).
Sensors are epoxy-encapsulated and optics are hermetically sealed.
SP100D
SP100C
Models/Dimensions
Range: 8 inches (20cm)
Beam: infrared, 880nm
Effective beam: .05 inch
(1,3mm diameter)
Cable (all 6-foot lengths):
SP100E: 2-wire ribbon cable
(white, green).
SP100R: 3-wire ribbon cable
(red, black, yellow).
SP100D, DB, C, CCF: 5-wire
ribbon cable (white, green,
red, black, yellow). See
hookup drawing.
SP100E &
SP100CCF
SP100DB
SP100R
OPPOSED Mode Sensors
SP100E and SP100R miniature opposed sensors have a slim right-angle design
which allows them to be mounted in very tight locations. The thin, flexible
ribbon cable which exits from one corner may be run in any direction away from
the sensing point. The SP100E and R have a wide beam angle for forgiving line-
of-sight alignment. Alignment is easily made exact (and monitored) using the
AID™ LED on the MICRO-AMP module.
DIFFUSE Mode Sensors
Models SP100D and SP100DB are general-purpose miniature diffuse sensors
which detect the reflection of their own light from the surface of an object. The
SP100D is a right-angle design which is generally held in place using a #4 (3mm)
screw. The SP100DB ("B" = Barrel) is an in-line threaded barrel which typically
mounts through a 3/8" (10mm) diameter hole using the lock nuts which are
supplied. The optical response characteristics of these two sensors are identical.
CONVERGENT Mode Sensors
Models SP100C and CCF are ideally suited to applications where depth of field
is critical. The emitter and receiver are both directed at a point 0.1 inch (2,5mm)
ahead of the front surface. An aperture is included which, when attached,
narrows the depth of field (see curves, below). This is particularly useful when
it is necessary to detect an object while ignoring another object or a surface just
a fraction of an inch farther away. The high excess gain at the focus allows
detection of objects of low reflectivity. The SP100C and CCF differ only in
housing style. Model SP100C is for general application. Model SP100CCF is
used where a narrow profile is important for mounting.
E
X
C
E
S
S
G
A
I
N
I
E
X
C
E
S
S
G
A
I
N
I
E
X
C
E
S
S
G
A
I
N
I
1000
1000
1000
100
100
100
10
.01 IN
.01 IN
10
10
.1 IN
1
Excess Gain
1
1
SP100C, SP100CCF
SP100D, SP100DB
with
aperture
Range based on 90%
reflectance white test card
1 IN
.1 IN
.1 IN
DISTANCE
DISTANCE
DISTANCE
SP100E/R
without
aperture
(Range based on
90% reflectance
white test card)
10 IN
1 IN
1 IN
10 IN
10 IN
100 IN
I
N
C
H
E
S
I
N
C
H
E
S
I
N
C
H
E
S
1.5
1.5
.05
.05
DISTANCE TO 90% WHITE TEST CARD--INCHES
.05
.5
.5
.1
.05
DISTANCE TO 90% WHITE TEST CARD--INCHES
1
0
1
0
.1
.1
0
.1
0
Beam Pattern
0
0
SP100E/R
SP100C, CCF
OPPOSED DISTANCE --INCHES
2
.15
.3
SP100D, DB
with aperture
.30
.6
4
.45
.9
6
without aperture
.60
1.2
8
.75
1.5
10