E3ZD66 Omron, E3ZD66 Datasheet - Page 8

• Manufacturer Part Number: E3ZD66
• Description: Photoelectric Sensor
• Manufacturer: Omron

Specifications of E3ZD66

• Output Current: 100mA
• Sensor Output: NPN
• Supply Voltage Range Dc: 12V To 24V
• Reflector Distance Min: 0.2"
• Mounting Type: Bracket
• Switch Terminals: Cable
• Reflector Distance Max: 3.9"
• Supply Voltage Min: 12VDC
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

The E3Z-T@2-G0 is equipped with an emission stop function. Ratings and specifications of this function are given in the following table.
Oil-resistant
* Values in parentheses indicate the minimum required distance between the Sensor and Reflector.
Item
Emission stop
function
Item
Sensing distance
Spot diameter
Standard sensing object
Minimum detectable object
Differential travel
Directional angle
Light source (wavelength)
Power supply voltage
Current consumption
Control output
Protection circuits
Response time
Sensitivity adjustment
Ambient illumination (Receiver side)
Ambient temperature range
Ambient humidity range
Insulation resistance
Dielectric strength
Vibration resistance
Shock resistance
Degree of protection
Connection method
Indicator
Weight
(packed
state)
Material
Accessories
Model
Pre-wired cable (2 m)
Connector (M8, 4 pins)
Case
Lens
NPN
Input
Response time
PNP
out-
out-
put
put
Output and Modes
M8 Pre-wired connector E3Z-T61K-M3J
M8 Pre-wired connector E3Z-T81K-M3J
Sensing method
Pre-wired Models E3Z-T61K
Pre-wired Models E3Z-T81K
Sensing method
Through-beam models, NPN output: E3Z-T62/T67-G0, PNP output: E3Z-T82/T87-G0
<NPN models> Emission OFF: Short-circuit to 0 V or 1.5 V max. (Outflow current 1 mA max.), Emission ON: Discon-
nected (Leakage current 0.1 mA max.)
<PNP models> Emission OFF: Short-circuit to +DC (Power supply plus side) or +DC-1.5 V max. (Inlet current 3 mA
max.), Emission ON: Disconnected (Leakage current 0.1 mA max.)
Operate or reset: 0.5 ms max.
15 m
Opaque: 12-mm dia. min.
Both emitter and receiver:
3 to 15
Infrared LED (870 nm)
12 to 24 VDC 10%, ripple (p-p): 10% max.
35 mA max. (Emitter:
15 mA max., Receiver:
20 mA max.)
Load power supply voltage: 26.4 VDC max., Load current: 100 mA max.
Residual voltage: Load current of less than 10 mA: 1 V max.
Load current of 10 to 100 mA: 2 V max.
Open collector output (NPN/PNP depending on model)
Light-ON/Dark-ON selectable
Reversed power supply
polarity protection, Output
short-circuit protection,
and Reversed output po-
larity protection
Operate or reset: 1 ms max.
One-turn adjuster
Incandescent lamp: 3,000 lx max.
Sunlight: 10,000 lx max.
Operating: 25 to 55 C, Storage: 40 to 70 C (with no icing or condensation)
Operating: 35% to 85%, Storage: 35% to 95% (with no condensation)
20 M
1,000 VAC, 50/60 Hz for 1 min
Destruction: 10 to 55 Hz, 1.5-mm double amplitude for 2 hours each in X, Y, and Z directions
Destruction: 500 m/s
IP67 (IEC), Oil resistant models: IP67 (IEC) (in-house standards: oilproof), excluding cables and connectors
Pre-wired cable (standard length: 2 m), M8 Pre-wired Connector
Operation indicator (orange)
Stability indicator (green)
Emitter has power indicator (orange) only.
Approx. 120 g
Approx. 50 g
PBT (polybutylene terephthalate)
Modified polyarylate
Instruction manual (Neither Reflectors nor Mounting Brackets are provided with any of the above models.)
Through-beam
min. at 500 VDC
2
3 times each in X, Y, and Z directions
---
E3Z-R61K
E3Z-R61K-M3J
E3Z-R81K
E3Z-R81K-M3J
3 m (150 mm)
(when using E39-R1S)
2 m (100 mm)
(when using E39-R1)
Opaque: 75-mm dia. min.
2 to 10
Red LED (660 nm)
30 mA max.
Reversed power supply polarity protection, Output short-circuit protection, Mutual in-
terference prevention, and Reversed output polarity protection
Approx. 65 g
Approx. 30 g
Methacrylic resin
Retro-reflective
*
*
---
---
E3Z-D61K
E3Z-D61K-M3J
E3Z-D81K
E3Z-D81K-M3J
100 mm
(white paper: 100
100 mm)
20% max. of setting distance
Infrared LED (860 nm)
Modified polyarylate
Diffuse-reflective
---
---
E3Z-D62K
E3Z-D62K-M3J
E3Z-D82K
E3Z-D82K-M3J
1 m
(white paper: 300
300 mm)
E3Z
8