QS18UPAE BANNER ENGINEERING, QS18UPAE Datasheet - Page 5

• Manufacturer Part Number: QS18UPAE
• Description: Ultrasonic Sensor
• Manufacturer: BANNER ENGINEERING
• Type: Ultrasonicr

Specifications of QS18UPAE

• Sensing Range Min: 50mm
• Sensing Range Max: 500mm
• Switching Frequency: 300kHz
• Operating Temperature Range: -20°C To +60°C
• Supply Voltage: 30VDC
• Sensor Terminals: Cable
• Control Output Type: PNP
• Frequency: 300kHz
• Body Style: Miniature
• Brand/series: World-Beam®
• Current, Switching: 100 mA
• Function: Proximity
• Ip Rating: IP68
• Mounting Type: Threaded
• Output: PNP, SPST
• Primary Type: Proximity
• Range, Measurement: 500 mm
• Technology: Ultrasonic
• Termination: 4-Wire Cable
• Voltage, Supply: 30 VDC
• Accessories Available: Cordsets, Brackets and Wave Guide
• Sensor Output: PNP

Figure 4. Using the Auto-Window feature
Position
Position
Output OFF
- 10 mm
- 10 mm
Output ON
Banner Engineering Corp. • Minneapolis, MN U.S.A
www.bannerengineering.com • Tel: [phone]
Normally Open Operation
Normally Closed Operation
for programming each output
• P ush and hold
• P osition the target
• “ Click” the push button
• W ithout moving the
push button
for the first limit
target, “click” the
push button again
Taught Position
Taught Position
0.04 sec. < “click” < 0.8 sec
Output OFF
Output ON
...
...
Push Button
...
...
Output OFF
Output ON
Position
+ 10 mm
Position
+ 10 mm
.
D
D
...
Procedure
Teaching the same limit twice automatically centers a 20 mm window on the taught
position.
General Notes on Programming
• T he sensor will return to RUN mode if the first TEACH condition is not registered within
• A fter the first limit is taught, the sensor will remain in PROGRAM mode until the
• T o exit PROGRAM mode without saving any changes, press and hold the programming
Figure 5. An application for the Auto-Window feature (retroreflective mode)
...
120 seconds.
TEACH sequence is finished.
push button > 2 seconds (before teaching the second limit). The sensor will revert to
the last saved program.
• N o action required; sensor is ready for 1st
• Position the target for the center of window
• S ingle-pulse the remote line
• W ithout moving the target,
limit teach
single-pulse the remote line
again
Sensor
Sensor
Output
Output
OFF
ON
WORLD BEAM
0.04 sec. < T < 0.8 sec
Range
Teaching Limits Using the Auto-Window Feature
Near
D
Remote Line
or
or
.
®
QS18U Series Ultrasonic Sensors
T
T
T
T
Any object in this area will switch
the output, whether or not the object
returns a good signal to the sensor.
Sensing Distance
or
Output OFF
Output LED: ON Red
Power LED: ON Green (good signal) or
Power LED: Must be ON Green
Output LED: Flashing Red
Output LED: ON Red
Output LED: Yellow or OFF
Output LED: Flashing Red
T
T
T
T
T
T
Teach Unacceptable
Teach Unacceptable
T
T
T
T
T
T
ON Red (no signal)
Teach Accepted
Teach Accepted
T
T
T
T
T
T
Position
-10 mm
T
T
Result
T
T
T
T
(background surface)
Taught Position
T
T
P/N 119287 rev. E
Output ON
T
T
T
T
Position
+10 mm
T
T
T
T
T
T
5