T30UXDB BANNER ENGINEERING, T30UXDB Datasheet - Page 4

• Manufacturer Part Number: T30UXDB
• Description: T30UX Series W/ Discrete Output
• Manufacturer: BANNER ENGINEERING

Specifications of T30UXDB

• Range: 200 Mm To 2 M
• Input: 10 To 30V Dc
• Output: NPN PNP NO NC Selectable
• Body Style: Round
• Range, Measurement: 200 mm to 2 m
• Response Time: 92 ms
• Voltage, Supply: 10-30 VDC
• Accessories Available: Cordsets and Brackets
• Lead Free Status / Rohs Status: RoHS Compliant part

U-GAGE
4
General Notes on Teaching
• The sensor will return to RUN mode if the first TEACH condition is not registered within 120 seconds
• T o exit TEACH mode without saving any changes, press and hold the Discrete push button or remote
• A fter the first limit is taught, the sensor will remain in TEACH mode until the TEACH sequence is
* Sensor will not Teach or indicate “Teach Not Accepted” when there is no signal present (Signal LED Red or Flashing Red)
finished or exited by a 2 second hold on the Discrete push button or remote line.
after the initial 2 second hold on Discrete push button.
line > 2 seconds (before teaching the second limit). The sensor will revert to the last saved limits.
P/N 138381 rev. B
...
• P ush and hold
• P osition the target for the
• “ Click” the Discrete
• P osition the target for the
• “ Click” the Discrete
...
...
Discrete push button
for > 2 seconds
first limit
(120 second time out)
push button
second limit
(no time out)
push button
®
Teaching Minimum and Maximum Limits
...
T30UX Series with Discrete Output
Procedure
D
0.04 sec. < “click” < 0.8 sec
D
Push Button
...
Power LED: OFF
Output LED: ON
Signal LED: Must be ON Red or
Power LED: OFF
Output LED: Flashing
Output LED: ON
Signal LED: Must be ON Red or
Output LED: ON or OFF,
Power LED: ON
Output LED: Flashing
Power LED: OFF
...
Teach Not Accepted
Teach Not Accepted
Teach Accepted
Teach Accepted
or
Flashing Red*
Flashing Red
.
depending on NO or
NC Mode
Result
D
or
• N o action required; sensor
• P osition the target for the
• S ingle-pulse the
• P osition the target for the
• S ingle-pulse the
is ready for 1st limit teach
first limit
remote line
second limit
(no time out)
remote line
Procedure
or
Banner Engineering Corp. • Minneapolis, MN U.S.A
www.bannerengineering.com • Tel: [phone]
Figure 2. Teaching independent minimum and
T
0.04 sec. < T < 0.8 sec
T
T
T
Remote Line
Output OFF
Output ON
maximum limits
Normally Open Operation
Normally Closed Operation
None
Signal LED: Must be ON Red or
Power LED: OFF
Output LED: Flashing
Power LED: ON
Signal LED: Must be ON Red or
Output LED: ON or OFF,
Power LED: ON
Output LED: Flashing
Power LED: OFF
Minimum
Minimum
Limit
Limit
Teach Not Accepted
Teach Not Accepted
Output ON
Output OFF
Teach Accepted
Teach Accepted
T
T
T
.
T
T
T
Flashing Red*
Flashing Red
depending on NO or
NC Mode
Result
T
T
T
T
T
T
Maximum
Maximum
T
T
T
T
Limit
Limit
T
T
T
T
Output OFF
Output ON
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T