61F-GPN2 240AC Omron, 61F-GPN2 240AC Datasheet - Page 6

• Manufacturer Part Number: 61F-GPN2 240AC
• Description: LEVEL CONTROLLER, MINI, 240V
• Manufacturer: Omron

Specifications of 61F-GPN2 240AC

• Supply Voltage: 240V
• Response Time: 80ms
• Power Consumption: 3.2W
• Svhc: No SVHC (15-Dec-2010)
• Ac Coil Power: 3.2VA
• Approval Bodies: CE, CSA, SEV, UL Recognised
• Contact Current Max: 5A

■ Precautions
Precautions for Safe Use
1. Precautions for the environment
• Use and preserve within the proper temperature and humidity
• Temperature of surroundings for preservation (including during
• Do not install, among others, near heat devices such as coils or
• Avoid preserving (including during transportation) and using in a
• Preserve and use without exposing to danger of explosion, flamma-
• Avoid preserving (including during transportation) and using in a
• Avoid preserving (including during transportation) and using in a
• Do not install the product near devices generating strong high-fre-
2. Cautions for Use
• Read the instruction manual and catalog before operating and
• Fit socket(s) and DIN rail(s) so that the screws are tight.
• Be sure to fit socket(s) to DIN rail(s) without fail.
• Use metal strengthener(s) to maintain a firm connection between
• Read the instructions manual and catalog before the operation and
• When fitting crimping terminal(s) to terminal screw(s), use a tight-
• Use power supply of appropriate specifications to provide control
• Do not put power line(s), high-voltage cable(s) and wire(s) of elec-
• Shorten the distance for wiring between the model 61F and elec-
• Be sure to ground common electrode terminal(s). Doing so can
• Use the product within the noted supply voltage and rated load.
6
Do not touch the terminals while power is being supplied.
Doing so may possibly result in electric shock. Make sure
that the terminal cover is installed before using the
product.
Do not attempt to disassemble, repair, or modify the
product. Doing so may occasionally result in minor or
moderate injury due to electric shock.
described in the specifications.
transportation) and use:
other devices having coils, etc.
humid place, in a corrosive gas environment, outdoors and in a
place which receives direct sunlight.
ble dust, gas and vapor, excessive dust, and saline spray or drop-
lets.
place which is vulnerable to flooding or oil spillage.
place where vibrations and impacts are strong. Similarly, avoid
using next to a high-capacity contactor which may impacts at oper-
ation. Doing so causes malfunctions such as chattering, etc.
quency waves or surges. When using a noise filter, check the volt-
age and current and install it as close to the product as possible.
maintaining the product.
If the screws are not tight, DIN rail(s), socket(s), the product and
cable(s) may lead to come off.
the product and socket(s).
maintenance of the product.
ening torque of between 0.45 and 0.6 N·m
source(s), inputs, etc., and to wire cables.
[Recommended cable to wire between the model 61F and elec-
trode(s) when using three-core cabtire cable(s) of completely insu-
lated 600 V 0.75 mm VCT: 50 m max.]
trode circuit(s) in the same duct nor wire closely. Doing so causes
malfunctions by getting vulnerable to induction noise.
trode holders as much as possible. Long distance for wiring may
causes malfunctions because stray capacitance may influence
operation, or abnormal surges or noise may run through electrode
circuit(s).
reduce some effects of noise.
Conductive Level Controller
!WARNING
-
!CAUTION
10 to 55
•
C, humidity: 45 to 85%.
61F-GP-N2
• Before using, recheck the application, wiring, power supply, etc.
• Check the application and power supply.
• Firmly ground the earth terminal No.4.
• Make sure that electrode probes in the liquid do not come in con-
• Tighten nuts for electrode probe(s) firmly.
• Prevent flotage from attaching to electrode.
• This device is not available when the resistance is too high and is
Power supply (AC 220 V, AC 230 V) consists of other specifications.
If the power voltage is not AC 200 V or AC 100 V, follow the instruc-
tions described on the device.
tact one another as it may cause malfunction. Use separator when
connecting.
not conductive such as oil.