IFMA0065 Red Lion Controls, IFMA0065 Datasheet - Page 5

• Manufacturer Part Number: IFMA0065
• Description: Frequency/Analog Converter
• Manufacturer: Red Lion Controls

Specifications of IFMA0065

• Width: 3.12"
• Signal Input Type: Selectable Current Or Voltage
• Configuration Setup: DIP Switch
• Supply Voltage Max: 250VAC
• Iso-amp Mounting Type: DIN Rail
• Input Accuracy: +/- 0.1% Of FS
• Signal Output Type: Selectable Current Or Voltage
• Rohs Compliant: Yes
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

OUTPUT INDICATION
Over range on the output : The Output LED (red) turns on and the
Low Frequency Cut-Out : The Output LED (red) turns on to
Invalid Entry during Set-up : The Input LED (green) and the
1.0 Operating Mode (Analog Output)
2.0 On-Line Input Range Setting Using Actual Input Signal Or Frequency Generator
Output is “clamped” at the maximum level.
indicate the input frequency is below the Zero Frequency setting.
Output LED (red) alternately blink until a valid entry is made.
BLINKS
OUTPUT
GREEN
INPUT
PUSH-BUTTON
LED
RED
LED
OFF
BLINKS
OUTPUT
GREEN
INPUT
LED
RED
LED
OFF
PREFERRED
O U
IN
T
O U
IN
T
Step 1.2
Step 1.4
Step 1.3
METHOD
Step 2.2
Step 2.4
PUSH-BUTTON
PUSH-BUTTON
ROTARY
SWITCH
4
Step 1.1
4
5
Setting ‘2’
Selected
Step 2.1
5
6
0
5
6
7
7
1.1 Place DIP switch 4 to the ON (up) position and DIP switches 5, 6, and 7 as shown.
1.2 Green input LED blinks the Setting corresponding to the Operating Mode shown below, pauses


1.3 Press the push-button. The Green input LED blinks rapidly to indicate the Operating mode
1.4 Turn the rotary switch to the selected numerical value for the output desired (see the list in Step
1.5 Press the push-button. The Green input LED blinks value entered, pauses, and repeats the new



*
2.1 Place DIP switch 4 to the ON position and DIP switches 5, 6, and 7 as shown.
2.2 The Green input LED blinks the existing Input Range setting as shown in the examples below.

2.3 Apply the maximum input signal.
2.4 Press the push-button. The Green input LED blinks rapidly. The acquisition process takes two


2.5 Press the push-button. The Green input LED blinks the new Input Range setting. This section
*
Section complete; place DIP switch 4 to the Down position for normal operation, or change DIP
If the new input range setting is valid, the Green input LED turns on solid. Continue to Step 2.5.
Section complete; place DIP switch 4 to the Down position for normal operation, or change DIP
Factory calibration values are restored when the Operating Mode is changed.
Otherwise, continue with Step 1.3.
If the new Operating mode setting is acceptable, this section is complete
If the new Operating mode setting is not the desired setting, repeat from Step 1.3.
If the Red output LED blinks, the rotary switch numerical value is invalid. Repeat Steps 1.4
and 1.5.
switches 5, 6, and 7 for the next Configuration Section.
Otherwise, continue with Step 2.3.
If Red output LED blinks, the new input range setting is invalid, outside the acceptable 1 Hz
to 25 KHz range. Repeat Steps 2.3 and 2.4.
switches 5, 6, and 7 for the next Configuration Section.
If the existing Input Range setting is your desired requirement, this section is complete
If existing operating mode setting is your desired requirement, this section is complete
1
and repeats the value.
setting is now accessed.
1.2).
Operation setting.
Six full digits of numerical information blink with a short pause between digits and a longer
pause before repeating. The first five digits are the existing input range setting of the frequency
magnitude. The sixth digit is the frequency resolution (the number of digits to the right of the
decimal point).
seconds plus one period of the input signal.
is complete
Factory Setting Example
Result: 10.000 KHz
1 blink
2 sec pause
single flash
2 sec pause
single flash
2 sec pause
single flash
2 sec pause
single flash
2 sec pause
single flash
4 sec pause
Frequency
0
Parameter
Operating Mode
Input Range
Minimum Response
Maximum Response
0
5
0
*
. Verify the Input Range setting as shown in Step 2.2.
0
Resolution
Setting
1
0
0
0
0
0
1
2
3
4
0
Frequency
setting
Resolution
Operating Mode
Setting
10.000
0 to 10 VDC
4
0
0
0 to 5 VDC
0 to 20 mA
4 to 20 mA
FACTORY SETTINGS
Value
4 to 20 mA
10 KHz
5 msec
1024 times Input Range Period (102 msec, 9.8 Hz)
2
2 blinks
2 sec pause
5 blinks
2 sec pause
single flash
2 sec pause
5 blinks
2 sec pause
single flash
2 sec pause
2 blinks
4 sec pause
Frequency
5
Result: 250.50 Hz
Additional Example:
0
5
0
*
.
Resolution
2
5
0
5
0
2
2
Frequency
setting
Resolution
*
*
.
.