IQ65033QMA10END-G SYNQOR, IQ65033QMA10END-G Datasheet
IQ65033QMA10END-G
Specifications of IQ65033QMA10END-G
Related parts for IQ65033QMA10END-G
IQ65033QMA10END-G Summary of contents
Page 1
... The -48 V output voltage is conditioned for smooth operation through severe input transient events. The iQor is designed thermally and electrically to drive high power wide-range-input DC/DC converters such as the 300 W SynQor PQ60120QEA25. RoHS Compliant see last page. Operational Features • Input ORing for A & B power feeds (MOSFET-based for low power dissipation) • ...
Page 2
... Flanged Pin Lowest Load Board See Note 8 Component Pin No. Name www.synqor.com 36-75 V Input: 5.0 V/ 3.3 V Outputs Current: Quarter-brick Package: 0.100 (2.54) 14 0.150 13 (3.81 Bottom side Clearance 0.064 ±0.028 (1.63 ±0.71) PIN DESIGNATIONS Function -48V_A Negative A Feed (Externally Fused) ...
Page 3
... Doc.# 005-IQ5033S Rev. H 36-75 V Input: 5.0 V/ 3.3 V Outputs Current: Quarter-brick Package: Notes & Conditions Limited by internal TVS zener diode 1ms transient, square wave No damage, low current, output diode clamped Subject to thermal derating; see Figures 1 & 3 Subject to the Threshold Protocol used 25º ...
Page 4
... V 0.4 0 µA www.synqor.com Doc.# 005-IQ5033S Rev. H 36-75 V Input: 5.0 V/ 3.3 V Outputs Current: Quarter-brick Package: Units Notes & Conditions input feed voltage -48V_A/B; see Figure A V “ V “ load on 3.3V/5.0V outputs, Vin = -48V mW µ ...
Page 5
... Needle Flame Test (IEC 695-2-2) IEC 61000-4-2 GR-1089-CORE Telcordia (Bellcore) GR-513 • An external input fuse must always be used to meet these safety requirements. Contact SynQor for official safety certificates on new releases or download from the SynQor website. QUALIFICATION TESTING Parameter P # Units ...
Page 6
... Vin, -48V output @ 4 A). Figure 6: 8.70ms zero volt transient (564uF electrolytic hold-up capaci- tor CH, 100uF electrolytic filter capacitor CF Input Feed A/B Voltage (20V/div VRTN_OUT w.r.t. -48V_OUT (20V/div HU_CAP w.r.t. -48V_OUT (20V/div 3.3V_OUT (200mV/div). www.synqor.com 36-75 V Input: 5.0 V/ 3.3 V Outputs: ...
Page 7
... Figure 10: Management Power turn on transient at 50% load (4ms/div). Load capacitance: 10uF ceramic capacitor 3.3Vout (1V/div 5.0Vout (1V/div). Figure 12: 3.3Vout ripple at nominal input voltage at rated load current (20mV/div). Load capacitance: 10uF ceramic capacitor. Bandwidth: 500MHz. www.synqor.com 36-75 V Input: 5.0 V/ 3.3 V Outputs Current: ...
Page 8
... Among other data, each feed voltage and each enable voltage is reported through the I C port. These voltages can be compared with the voltages 2 reported by the shelf manager to determine whether any board fuse is blown. www.synqor.com 36-75 V Input: 5.0 V/ 3.3 V Outputs Current: ...
Page 9
... Management Power: converter delivers both 3.3V and a low power 5.0V relative to LOGIC_GND. Over-current protection operates in constant current with a hiccup mode if the output voltage drops too far. Output over-voltage circuitry is included with a redundant refer- ence and optocoupler. www.synqor.com 36-75 V Input: 5.0 V/ 3.3 V Outputs ...
Page 10
... Management power Alarm 38.4 V 38.9 V typ. typ. A/B - (-48V_A/B) RTN Holdup event 38.5 V typical (Depends 100ms on version) www.synqor.com 36-75 V Input: 5.0 V/ 3.3 V Outputs Current: Quarter-brick Package: 34.6 V typ. (Pull-up voltage lost) 34.0 (Depends on version) Output is off after delay if input voltage doesn’ ...
Page 11
... V Input: 5.0 V/ 3.3 V Outputs Current: Quarter-brick Package: 41. 8.70ms Time (ms) The operating life of electrolytic SynQor recommends A built-in circuit automatically discharges the Doc.# 005-IQ5033S Rev. H 05/27/10 43.0V 36. Page 11 ...
Page 12
... Holdup capacitor C H -48V_A -48V_B VRTN_A SynQor iQor VRTN_B ATCA Power Input Module ENABLE_A ENABLE_B interface on full- SHELF_GND featured version only www.synqor.com 36-75 V Input: 5.0 V/ 3.3 V Outputs Current: Quarter-brick Package Hold-up Charge Voltage (V) Shield Plane* Payload Power 100 F µ Converter ...
Page 13
... Hotswap switch is OFF 8) ACK (Data_Pointer is automatically incremented to 23h). Hotswap switch Unit will respond with the value of -48V_B (register 23h). 10) NACK. Output voltage is below threshold 11) Stop Transmission. Output voltage is above threshold www.synqor.com Doc.# 005-IQ5033S Rev. H 36-75 V Input: 5.0 V/ 3.3 V Outputs Current: Quarter-brick Package: ...
Page 14
... External programming resistances for address for 2 R√W write (R√ 5Eh 5Ch 5Ah 58h 56h 54h 52h 50h Table address selection. 2 www.synqor.com Doc.# 005-IQ5033S Rev. H 36-75 V Input: 5.0 V/ 3.3 V Outputs Current: Quarter-brick Package: C Address address selection xyz from Table 3 R (W) 111 Open ...
Page 15
... Warranty SynQor offers a three (3) year limited warranty. Complete warranty informa- tion is listed on our website or is available upon request from SynQor. Information furnished by SynQor is believed to be accurate and reliable. However, no responsibility is assumed by SynQor for its use, nor for any infringements of patents or other rights of third parties which may result from its use ...