SMT15E-12W3V3-TJ Emerson Network Power, SMT15E-12W3V3-TJ Datasheet - Page 17

• Manufacturer Part Number: SMT15E-12W3V3-TJ
• Description: 10-14Vin, 0.8-3.63V@15A, 1.30" X 0.53" X 0.32, 94%Eff, SMT, T&R Packaging, RoHS 6
• Manufacturer: Emerson Network Power

Specifications of SMT15E-12W3V3-TJ

• Product: Non-Isolated / POL
• Output Power: 55 W
• Input Voltage Range: 10 V to 14 V
• Input Voltage (nominal): 12 V
• Number Of Outputs: 1
• Output Voltage (channel 1): 0.8 V to 3.63 V
• Output Current (channel 1): 15 A
• Package / Case Size: 33.02 mm x 13.46 mm x 8.13 mm
• Output Voltage: 0.8 V to 3.63 V
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

Ordering Information
Sample below is 1200 W case with 12 V @ 50 A; 5 V @ 60 A; 24 V @ 8.5 A; 12 V @ 10 A; 12 V @ 4 A; extended hold-up with no options.
Adjustment range
Margining
Overall reg
Ripple
Dynamic response
Recovery time
Overcurrent protection
Short-circuit protection
Overvoltage protection
(measured at sense
connection)
Reverse voltage
protection
Thermal protection
Remote sense
Single wire parallel
DC OK
Minimum load
Housekeeping standby
Module inhibit
Switching frequency
Output/output isolation
VME signal option board
Output
Case Size (mm)
4 = 2.5" x 5" x 10";
400 W-600 W, 5 Slots
6 = 2.5" x 5" x 11";
600 W-800 W, 5 Slots
8 = 2.5" x 7" x 10";
800 W-1000 W, 6 Slots
1 = 2.5" x 8" x 11";
1000 W-1200 W, 7 Slots
(63.5 x 127 x 254)
(63.5 x 127 x 279.4)
(63.5 x 177.8 x 254)
(63.5 x 203.2 x 279.4)
MP1
Case Size
±10% minimum all outputs
±4-6% nominal
0.4% or 20 mV maximum
(36 W modules 4% maximum)
RMS: 0.1% or 10 mV, whichever is greater; Pk-Pk: 1.0% or
50 mV, whichever is greater; bandwidth limited to 20 M Hz
<2% or 100 mV, with 25% load step
To within 1% in <300 μ second
Single, main of dual output module 105-120% of rated
output current
Protected for continuous short-circuit
Recovery is automatic upon removal of short
Single output modules
100% of rated output current
All outputs disabled when internal temp exceeds safe
operating range
>5ms warning (AC OK signal) before shutdown
Up to 0.5 V total drop
(not available on triple output module)
Current share to within 2% of total rated current
-2% to -8% of nominal for any monitored output
Not required on single or triple output modules.
10% required on main of dual output modules
5 Vdc @1.0 A mA maximum present whenever AC input is
applied (optional 2.0 A available)
TTL, isolated, singles and dual
(both outputs) only
250k Hz
>1 Megohm
POR signal & quad external DC OK
For complete product specifications, technical reference notes and available product options, go to www.powerconversion.com.
- 3L - 2E - 1Q - 4LL
Module Codes
Module/Voltage/Option Codes
Module Codes:
(None) = 36 W Triple O/P (1 slot)
1 = 210 W Single O/P (1 slot)
2 = 360 W Single O/P (2 slot)
3 = 750 W Single O/P (3 slot)
4 = 144 W Dual O/P (1 slot)
5 - 9 = Future
Voltage Codes:
See Output Module Voltage/Current
table
Second - Voltage Code
Module/Voltage(s)
First - Module Code
Add-on Modules
HUP = Hold up module
VME = VME POR signal
3
Requires 1 slot each
Add-on Modules
2
2
- HUP
and isolated DC
Notes:
1. Single output modules only
2. Single and main of dual output modules only
3. Contact factory for optional preload if required
Environmental
Specifications
Safety
Operating
temperature
Storage/
vibration
Humidity
Storage
temperature
Temperature
coefficient
Cooling:
UL
CSA
IEC
VDE
BABT
CB
CE
Case Option Codes
First Digit
0 - 9 = parallel code
(See MP parallel codes table on
following page)
Second Digit
Standard Options
0 = no options
1 = rear air exhaust
3 = global enable
5 = option package
M = low leakage
N = low leakage plus option 1
P = low leakage plus option 3
R = low leakage plus option 5
(options 1 & 3)
Case Option Codes
UL1950
CSA22.2 No. 234 Level 5
IEC950, Class 1
EN60950-1
Compliance to EN 60950, BS 7002
Certificate and report
Mark
- 00
-20 °C to 50 °C (start @ 0 °C)
(derate each output linearly to
50% at 70 °C) (-20 °C to 40 °C
max. with rear air option)
MIL-HDBK 810E
95% non-condensing
-40 °C to 85 °C
0.02% per °C
Internal DC fan or customer
provided air (option)
Medium Power
Factory assigned
for modifications
Hardware Code
- ###
17