HFBR-0537 Avago Technologies US Inc., HFBR-0537 Datasheet
HFBR-0537
Specifications of HFBR-0537
HFBR-0537
Related parts for HFBR-0537
HFBR-0537 Summary of contents
Page 1
... The HFBR-15X7 transmitter is a high power 650 nm LED in The HFBR-15X7 transmitter low cost plastic housing designed to efficiently couple high power 650 nm LED in a low ...
Page 2
... Typical performance is at 25°C, 125 MBd, and is measured with typical values of all circuit components. 5. Standard cable is HFBR-RXXYYY plastic optical fiber , with a maximum attenuation of 0.24 dB/m at 650 nm and NA = 0.5. Extra low loss cable is HFBR-EXXYYY plastic optical fiber, with a maximum attenuation of 0.19 dB/m at 650 nm and NA = 0.5. ...
Page 3
... Average Modulated Power = ––—————————————————————— 3. High and low level LED currents refer to the current through the HFBR-15X7 LED. The low level LED “off” current, sometimes referred to as “ ...
Page 4
... Receiver Application Circuit Current Consumption Notes: 4. Performance in response to a signal from the HFBR-15X7 transmitter driven with the recommended circuit at 1-125 MBd over 1 meter of HFBR-R/EXXYYY plastic optical fiber or 1 meter of HFBR-H/VXXYYY hard clad silica optical fiber. 5. Terminated through a 50 Ω resistor there is no input optical power to the receiver, electrical noise can result in false triggering of the receiver. In typical applications, data encoding and error detection prevent random triggering from being interpreted as valid data ...
Page 5
V ECL SERIAL DATA SOURCE 0.1 µ – µF 0.1 µF 10 µF 0.1 µF 82 Ω 82 Ω ECL SERIAL DATA RECEIVER 120 Ω 120 Ω Figure 2. Recommended Power ...
Page 6
... WARNING: WHEN VIEWED UNDER SOME CONDITIONS, THE OPTICAL PORT MAY EXPOSE THE EYE BEYOND THE MAXIMUM PERMISSIBLE EXPOSURE RECOMMENDED IN ANSI Z136.2, 1993. UNDER MOST VIEWING CONDITIONS THERE IS NO EYE HAZARD. 6 with HFBR-25X6 receivers in data links operating at signal rates from 1 to 125 megabaud over 1 mm diameter plastic optical fiber or 200 µ ...
Page 7
... Optical Power measured at the end of 0.5 meter diameter plastic or 200 µm diameter hard clad silica optical fiber with a large area detector. 4. Typical value measured from junction to PC board solder joint for horizontal mount package, HFBR-1527. θ higher for vertical mount package, HFBR-1537. ...
Page 8
HP8082A PULSE BCP MODEL 300 GENERATOR 500 MHz BANDWIDTH SILICON AVALANCHE PHOTODIODE HP54002A 50 OHM 50 OHM BNC LOAD OSCILLOSCOPE RESISTOR INPUT POD Figure 1. Test Circuit for Measuring Unpeaked Rise and Fall Times. 2.4 0° C 2.2 25° C ...
Page 9
... Receiver HFBR-25X6 Series Description The HFBR-25X6 receivers contain a PIN photodiode and transimpedance pre-amplifier circuit in a horizontal (HFBR- 2526) or vertical (HFBR-2536) blue housing, and are designed to interface to 1mm diameter plastic optical fiber or 200 µm hard clad silica glass optical fiber. The receivers convert a received ...
Page 10
Electrical/Optical Characteristics (see Figure 1, Note 2). Parameter AC Responsivity 1 mm POF AC Responsivity 200 µm HCS RMS Output Noise Equivalent Optical Noise Input Power, RMS - 1 mm POF Equivalent Optical Noise Input Power, RMS - 200 µm ...
Page 11
Figure 1. Recommended Power Supply Filter Circuit. Figure 2. Simplified Receiver Schematic. Figure 3. Typical Pulse Width Distortion vs. Peak Input Power. 11 Figure 4. Typical Output Spectral Noise Density vs. Frequency. Figure 5. Typical Rise and Fall Time vs. ...
Page 12
... Avago, Avago Technologies, and the A logo are trademarks of Avago Technologies, Limited in the United States and other countries. Data subject to change. Copyright © 2008 Avago Technologies Limited. All rights reserved. Obsoletes 5962-9376E 5965-6114E - February 20, 2008 HORIZONTAL MODULES HFBR-1537 HFBR-2526 HFBR-15X7 www.avagotech.com www.semiconductor.agilent.com Data subject to change. Copyright © 1999 Agilent Technologies, Inc. Obsoletes 5962-9376E (4/94) ...