135D106X9050C6E3 Vishay, 135D106X9050C6E3 Datasheet - Page 7

• Manufacturer Part Number: 135D106X9050C6E3
• Description: CAPACITOR TANT 10UF, 50V, 6.4OHM, AXIAL
• Manufacturer: Vishay
• Series: 135Dr

Specifications of 135D106X9050C6E3

• Capacitance Tolerance: ± 10%
• Voltage Rating: 50VDC
• Esr: 6.4ohm
• Capacitor Case Style: Axial
• No. Of Pins: 2
• Operating Temperature Range: -55°C To +85°C
• Capacitance: 10µF
• Capacitor Mounting: Through Hole
• Termination Type: Axial Leaded
• Rohs Compliant: Yes
• Tolerance: 10 %
• Termination Style: Axial
• Dimensions: 4.78 mm Dia. x 11.51 mm L
• Product: Tantalum Wet Hermetically Sealed
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

PERFORMANCE CHARACTERISTICS
1.
(1)
2.
3.
3.1 The surge voltage of capacitors is 115 % of rated DC
3.2 Surge Voltage Test: Capacitors shall withstand the
Document Number: 40024
Revision: 15-Nov-10
TYPICAL CURVES OF IMPEDANCE AS A FUNCTION OF FREQUENCY AT VARIOUS TEMPERATURES
100
1.0
0.1
10
Operating Temperature: Capacitors are designed to
operate over a temperature range of - 55 °C to + 200 °C.
Consult Vishay Sprague for information at + 200 °C. See
paragraph 9.3.
DC Working Voltage: The DC working voltage is the
maximum operating voltage for continuous duty at the
rated temperature.
Surge Voltage: The surge voltage rating is the
maximum voltage to which the capacitors should be
subjected
transients and peak ripple at the highest line voltage.
working voltage.
surge voltage applied through a 1000 Ω ± 10 % resistor
in series with the capacitor and voltage source at the
rate of one-half minute on, four and one-half minutes
100
+ 85 °C
UP TO
100
125
(V)
10
15
25
30
35
50
60
75
6
8
1K
under
“C” Case 33 µF, 50 V Capacitors
Wet Tantalum Capacitors Tantalum-Case with Glass-to-Tantalum
+ 125 °C
AT
(V)
10
15
20
23
30
40
50
65
85
4
5
7
any
+ 125 °C
10K
Frequency in Hz
conditions.
Hermetic Seal for - 55 °C to + 200 °C Operation
+ 175 °C
+ 85 °C
100K
AT
(V)
13
15
18
25
30
38
50
63
3
4
5
8
For technical questions, contact:
- 40 °C
- 55 °C
+ 25 °C
- 20 °C
This
+ 200 °C
1M
includes
(V)
AT
(1)
10M
3.3. Following the surge voltage test, the capacitance at
4.
4.1 Measurements shall be made by the bridge method at
5.
6.
6.1 The equivalent series resistance shall not exceed the
100
1.0
0.1
10
100
off, for 1000 successive test cycles at + 85 °C or
+ 125 °C.
and the equivalent series resistance and DC leakage
current will not exceed the values shown in the
“Standard Ratings Table” for each capacitor.
Capacitance Tolerance: The capacitance of all
capacitors shall be within the specified tolerance limits
of the nominal rating.
or referred to a frequency of 120 Hz at a temperature of
+ 25 °C. The maximum voltage applied to the capacitors
during measurement shall be 1 V
accuracy of the bridge shall be within ± 2 %.
Capacitance
capacitance change with temperature shall not exceed
the values given in the “Standard Ratings Table” for
each capacitor.
Equivalent Series Resistance: Measurements shall
be made by the bridge method at, or referred to, a
frequency of 120 Hz at a temperature of + 25 °C. A
maximum of 1 V
measurement.
maximum value in ohms listed in the “Standard Ratings
Table” for each capacitor.
[e-mail]
+ 25 °C shall not have changed by more than ± 10 %
1K
“K” Case 56 µF, 125 V Capacitors
+ 125 °C
Change
+ 85 °C
10K
Frequency in Hz
RMS
With
shall be applied during
100K
+ 25 °C
- 55 °C
- 40 °C
- 20 °C
Temperature:
RMS
. Measurement
www.vishay.com
1M
Vishay
135D
10M
The
7