ZICM357P2-1-B CEL, ZICM357P2-1-B Datasheet - Page 12

• Manufacturer Part Number: ZICM357P2-1-B
• Description: MOD EM357 ZIG 802.15.4 PCB ANT
• Manufacturer: CEL

Specifications of ZICM357P2-1-B

• Frequency: 2.405GHz ~ 2.475GHz
• Data Rate - Maximum: 250kbps
• Modulation Or Protocol: 802.15.4 Zigbee
• Applications: Home/Building Automation, Security, ZigBee™
• Power - Output: 20dBm
• Sensitivity: -100dBm
• Voltage - Supply: 2.7 V ~ 3.6 V
• Current - Receiving: 28mA
• Current - Transmitting: 170mA
• Data Interface: PCB, Surface Mount
• Memory Size: 192kB Flash, 12kB RAM
• Antenna Connector: On-Board, Trace
• Operating Temperature: -40°C ~ 85°C
• Package / Case: *
• Wireless Frequency: 2483.5 MHz
• Interface Type: SPI, TWI, UART
• Security: AES
• Operating Voltage: 3.6 V
• Output Power: 20 dBm
• Antenna: PCB Trace
• Operating Temperature Range: - 40 C to + 85 C
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With/related Products: EM357
• Other names: ZICM357P2-1; ZICM357P2-1

PROCESSING
Hand Soldering
Hand soldering is possible. When using a soldering iron, follow IPC recommendations (reference document IPC-7711)
Rework
The MeshConnect Module can be unsoldered from the host board. Use of a hot air rework tool should be programmable
and the solder joint and module should not exceed the maximum peak reflow temperature of 250 ºC.
Caution
thermal shock. Avoid overheating.
Warning
terminate warranty coverage.
Additional Grounding
Attempts to improve module or system grounding by soldering braids, wires, or cables onto the module RF shield cover is
done at the customer's own risk. The numerous ground pins at the module perimeter should be sufficient for optimum
immunity to external RF interference.
AGENCY CERTIFICATIONS
FCC Compliance Statement (Part 15.19) Section 7.15 of RSS-GEN
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
Warning (Part 15.21)
Changes or modifications not expressly approved by CEL could void the user's authority to operate the equipment.
20 cm Separation Distance
To comply with FCC/IC RF exposure limits for general population / uncontrolled exposure, the antenna(s) used for this
transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-located
or operating in conjunction with any other antenna or transmitter.
OEM Responsibility to the FCC Rules and Regulations
The MeshConnect Module has been certified per FCC Part 15 rules for integration into products without further testing or
certification. To fulfill the FCC certification requirements, the OEM of the MeshConnect Module must ensure that the
information provided on the MeshConnect Label is placed on the outside of the final product. The MeshConnect Module is
labeled with its own FCC ID Number. If the FCC ID is not visible when the module is installed inside another device, then
the outside of the device into which the module is installed must also display a label referring to the enclosed module. This
exterior label can use wording such as the following: “Contains Transmitter Module FCC ID: W7Z-ZICM357P2” or “Contains
FCC ID: W7Z-ZICM357P2”
The OEM of the MeshConnect Module must only use the approved antenna, (PCB Trace Antenna) that has been certified
with this module. The OEM of the MeshConnect Module must test their final product configuration to comply with Uninten-
tional Radiator Limits before declaring FCC compliance per Part 15 of the FCC rules.
1. This device may not cause harmful interference.
2. This device must accept any interference received, including interference that may cause undesired operation.
If temperature ramps exceed the reflow temperature profile, module and component damage may occur due to
Never attempt a rework on the module itself, e.g. replacing individual components. Such actions will
(Continued)
MeshConnect™ EM357 Module
Page 12