LQ104S1LG61 Sharp Microelectronics, LQ104S1LG61 Datasheet
LQ104S1LG61
Specifications of LQ104S1LG61
Available stocks
Related parts for LQ104S1LG61
LQ104S1LG61 Summary of contents
Page 1
... P S RODUCT PECIFICATIONS LQ104S1LG61 TFT-LCD Module Spec. Issue Date: June 8, 2007 AVC Liquid Crystal Displays Group No: LD-19604A ...
Page 2
...
Page 3
... LQ104S1LG61 SPEC No. DATE LD-19604A JUN.08.2007 RECORDS OF REVISION REVISED No. PAGE - - SUMMARY - 1 st Issue NOTE ...
Page 4
... Application This specifications applies to color TFT-LCD module, LQ104S1LG61 These specifications sheets are the proprietary product of SHARP CORPORATION(”SHARP) and include materials protected under copyright of SHARP. Do not reproduce or cause any third party to reproduce them in any form or by any means, electronic or mechanical, for any purpose, in whole or in part, without the express written permission of SHARP ...
Page 5
Outline specification. Parameter Display size Active area Pixel format Number of colors (Number of gray scale level) Pixel pitch Pixel configuration Display mode Unit outline dimensions *1 Mass Surface treatment *1: excluding backlight cables. Outline dimensions is shown in ...
Page 6
Input Terminals 4-1. TFT-LCD panel driving CN1 (LVDS signals , +3.3V / +5.0V DC power supply and Contorol signal) Corresponding connector:FI-SE20M (JAE) or FI-S20S (JAE) Pin No. Symbol GND 4 GND 5 ...
Page 7
R/L = High, U/D = Low R/L = High, U/D = High R/L = Low, U/D = Low R/L = Low, U/D = High ...
Page 8
LVDS Interface block diagram Using receiver Single LVDS interface, which equals THC63LVDF64A(THine),contained in a control IC ： Corresponding Transmitter ：DS90C363, DS90C363A, DS90C383, DS90C383A( THC63LVDF63A,THC63LVDM63A(THine), SN75LVDS84(Ti) （System Side） Controller LVDS Transmitter ６ R0∼R5 TxIN 0∼ 5 ６ G0∼G5 TxIN 6∼11 ...
Page 9
Backlight driving CN2 ,CN3 Used connector : BHR-02(8.0)VS-1N (JST) Corresponding connector : SM02(8.0)B-BHS-1-TB or -1N-TB (JST) Pin no. symbol 1 VHIGH Power supply for lamp (High voltage side) 2 VLOW Power supply for lamp (Low voltage side) 5. Absolute ...
Page 10
Electrical Characteristics 7-1. TFT-LCD panel driving Parameter Current dissipation Permissive input ripple voltage Input voltage range Differential input threshold voltage Input impedance (Differential input) Input voltage Input current1 Input current2 [Note1] Typical current situation : 16-gray-bar pattern. Vcc=+3.3V / ...
Page 11
Backlight driving The backlight system is an edge-lighting type with double CCFT (Cold Cathode Fluorescent Tube). The characteristics of single lamp are shown in the following table. (It is usually required to measure under the following condition. condition:IL=6.0mA,Ta=25℃±2℃,FL=60kHz.) Parameter ...
Page 12
The performance of the backlight, for example life time or brightness, is much influenced by the characteristics of the DC-AC inverter for the lamp. When you design or order the inverter, please make sure that a poor lighting caused ...
Page 13
Phase difference) Vsync Hsync Item(symbol) Hsync-Vsync Phase difference (T (Hsync-ENAB Phase difference) ENAB Hsync T HN Item Hsync-ENAB Phase difference (T 8-2 Display position Item Horizontal rising edge of ENAB rising edge of Hsync Vertical rising edge of Vsync ...
Page 14
Input Signals, Basic Display Colors and Gray Scale of Each Color Colors & Gray scale Gray Scale Black 0 0 − ...
Page 15
Optical Characteristics Parameter Viewing Horizontal θ21, θ22 angle Vertical range Contrast ratio Response Rise time Decay Chromaticity of white Chromaticity of red Chromaticity of green Chromaticity of blue Luminance of white White Uniformity [Note] The measurement shall be executed ...
Page 16
Definitions of viewing angle range: [Note2] Definition of contrast ratio: The contrast ratio is defined as the following. Contrast Ratio (CR) = [Note3] Definition of response time: The response time is defined as the following figure and shall be ...
Page 17
Precautions a) Be sure to turn off the power supply when inserting or disconnecting the cable sure to design the cabinet so that the module can be installed without any extra stress such as warp or twist. ...
Page 18
Luminance decreases rapidly when it is used for a long time or repeatedly under the environment of the low temperature or the module is being cooled. Please avoid ...
Page 19
... Japan MADE IN JAPAN Taiwan MADE IN TAIWAN China MADE IN CHINA : Taiwan Quantity of module TYPE LQ104S1LG61 LQ104S1LG61G QUANTITY DATE ※ R.C. （ RoHS Compliance ） means these parts have corresponded with the RoHS directive. LD19604A-16 10pcs 2007 ...
Page 20
LD19604A-17 ...
Page 21
...
Page 22
... ALL EXPRESS AND IMPLIED WARRANTIES, INCLUDING THE WARRANTIES OF MERCHANTABILITY, FITNESS FOR USE AND FITNESS FOR A PARTICULAR PURPOSE, ARE SPECIFICALLY EXCLUDED event will SHARP be liable any way responsible, for any incidental or consequential economic or property damage. NORTH AMERICA SHARP Microelectronics of the Americas 5700 NW Pacific Rim Blvd. Camas, WA 98607, U.S.A. Phone: (1) 360-834-2500 ...