LQ104S1DG61 Sharp Microelectronics, LQ104S1DG61 Datasheet

Page 1

... P S RODUCT PECIFICATIONS LQ104S1DG61 TFT-LCD Module Spec. Issue Date: June 8, 2007 AVC Liquid Crystal Displays Group No: LD-19603A ...

Page 2

...

Page 3

... LQ104S1DG61 SPEC No. DATE LD-19603A JUN.08.2007 RECORDS OF REVISION REVISED No. PAGE - - SUMMARY - 1 st Issue NOTE ...

Page 4

... Application This specification applies to color TFT-LCD module, LQ104S1DG61 These specification sheets are the proprietary product of SHARP CORPORATION(”SHARP) and include materials protected under copyright of SHARP. Do not reproduce or cause any third party to reproduce them in any form or by any means, electronic or mechanical, for any purpose, in whole or in part, without the express written permission of SHARP ...

Page 5

Outline specification. Parameter Display size Active area Pixel format Pixel pitch Pixel configuration Display mode Unit outline dimensions *1 Mass Surface treatment *1: excluding backlight cables. Outline dimensions is shown in Fig.1 Specifications 26 (10.4") Diagonal 211.2(H)×158.4(V) 800(H)×600(V) (1 ...

Page 6

Input Terminals 4-1. TFT-LCD panel driving CN1 Corresponding connector: DF9-41S-1V, DF9A-41S-1V, DF9B-41S-1V, DF9M-41S-1V Pin No. Symbol 1 GND 2 CK Clock signal for sampling each data signal 3 GND 4 Hsync Horizontal synchronous signal 5 Vsync Vertical synchronous signal ...

Page 7

R/L = High, U/D = Low R/L = High, U/D = High 4-2. Backlight driving CN2 ,CN3 Used connector : BHR-02(8.0)VS-1N (JST) Corresponding connector : SM02(8.0)B-BHS-1-TB(LF)(SN) or -1N-TB(LF) or -1R-TB(LF) (JST) Pin no. symbol 1 VHIGH Power ...

Page 8

Parameter Symbol V Input voltage V Supply voltage Temperature Topa [Note1]CK,R0∼R5,G0∼G5,B0∼B5,Hsync,Vsync,ENAB,R/L,U/D [Note2] Vcc-turn-on conditions 0<t1≦15ms 0<t2≦10ms 0<t3≦100ms 0<t4≦1s t5>200ms Vcc-dip conditions 1) 2.5V≦Vcc td≦10ms 2) Vcc<2.5V Vcc-dip conditions should also follow the Vcc-turn-on conditions [Note3] Humidity: 95%RH ...

Page 9

Typical current situation : 16-gray-bar pattern. Vcc=+3.3V/+5.0V [Note2] CK,R0~R5,G0~G5,B0~B5,Hsync,Vsync,ENAB, R/L,U/D [Note3] CK,R0~R5,G0~G5,B0~B5,Hsync,Vsync,ENAB, [Note4] R/L [Note5] U/D [Note6] See below block diagram of input interface. R0∼R5 G0∼G5 B0∼ ENAB CK R/L U/D ＶＣＣ 100Ω R0∼R5 100Ω ...

Page 10

Backlight driving The backlight system is an edge-lighting type with double CCFT (Cold Cathode Fluorescent Tube). The characteristics of single lamp are shown in the following table. (It is usually required to measure under the following condition. condition:IL=6.0mA,Ta=25℃±2℃,FL=60kHz.) Parameter ...

Page 11

The performance of the backlight, for example life time or brightness, is much influenced by the characteristics of the DC-AC inverter for the lamp. When you design or order the inverter, please make sure that a poor lighting caused ...

Page 12

Input Data Signals and Display Position on the screen Display position of input data D1,DH1 D2,DH1 D2,DH2 D1,DH2 D1,DH3 D1,DH600 D3,DH1 D800,DH1 D800,DH600 ...

Page 13

THp THc * Only when enable terminal is fixed “LOW” ...

Page 14

Input Signals, Basic Display Colors and Gray Scale of Each Color Colors & Gray scale Gray Scale Black 0 0 − ...

Page 15

Optical Characteristics Parameter Symbol Viewing Horizontal θ21, θ22 angle Vertical range Contrast ratio Response Rise time Decay Chromaticity of white Chromaticity of red Chromaticity of green Chromaticity of blue Luminance of white White Uniformity [Note] The measurement shall be ...

Page 16

Definitions of viewing angle range: [Note2] Definition of contrast ratio: The contrast ratio is defined as the following. Contrast Ratio (CR) = [Note3] Definition of response time: The response time is defined as the following figure and shall be ...

Page 17

Display Quality The display quality of the color TFT-LCD module shall be in compliance with the Incoming Inspection Standard. 12.Handling Precautions a) Be sure to turn off the power supply when inserting or disconnecting the cable sure ...

Page 18

If a minute particle enters in the module and adheres to an optical material, it may cause display non-uniformity issue, etc. Therefore, fine-pitch filters have to be installed to cooling and inhalation hole if you intend to install a ...

Page 19

No. Test item 1 High temperature storage test 2 Low temperature storage test 3 High temperature & high humidity operation test 4 High temperature operation test 5 Low temperature operation test 6 Vibration test (non- operating) 7 ...

Page 20

... Serial No. (5 digits) Assembly site code Model number Lot number (DATE) Quantity of module １０ ｐｃｓ Japan MADE IN JAPAN Taiwan MADE IN TAIWAN China MADE IN CHINA : Taiwan Quantity of module TYPE LQ104S1DG61 LQ104S1DG61G QUANTITY 10pcs DATE 2007 ...

Page 21

...

Page 22

...

Page 23

... ALL EXPRESS AND IMPLIED WARRANTIES, INCLUDING THE WARRANTIES OF MERCHANTABILITY, FITNESS FOR USE AND FITNESS FOR A PARTICULAR PURPOSE, ARE SPECIFICALLY EXCLUDED event will SHARP be liable any way responsible, for any incidental or consequential economic or property damage. NORTH AMERICA SHARP Microelectronics of the Americas 5700 NW Pacific Rim Blvd. Camas, WA 98607, U.S.A. Phone: (1) 360-834-2500 ...