LQ035Q7DB02R Sharp Microelectronics, LQ035Q7DB02R Datasheet
LQ035Q7DB02R
Specifications of LQ035Q7DB02R
Available stocks
Related parts for LQ035Q7DB02R
LQ035Q7DB02R Summary of contents
Page 1
... P S RODUCT PECIFICATIONS LQ035Q7DB02R TFT-LCD Module Spec. Issue Date: June 16, 2005 No: LCP-05011 Mobile Liquid Crystal Displays Group ...
Page 2
...
Page 3
RECORDS OF REVISION ＭＯＤＥＬ Ｎｏ：ＬＱ０３５Ｑ７ＤＢ０２Ｒ ＳＰＥＣ Ｎｏ ：ＬＣＰ−０５０１１ NO. 2005.06 .15 ＬＣＰ−０５０１１ PAGE SUMMARY - - NOTE 1 st Issue ...
Page 4
This publication is the proprietary of SHARP and is copyrighted, with all rights reserved. Under the copyright laws, no part of this publication may be reproduced or transmitted in any form or by any means, electronic or mechanical for any ...
Page 5
... Application This specification applies to LQ035Q7DB02R. (2) Overview This module is a color reflective and active matrix LCD module incorporating amorphous silicon TFT (Thin Film Transistor), named AD-TFT(Advanced TFT composed of a color TFT-LCD panel, driver ICs, an FPC, a back light, a touch panel and a back sealed casing. It isn’t composed control circuit. ...
Page 6
Table2 Pin No. Symbol I/O VDD Power supply of gate driver(high level) − 1 AGND − MOD I Control signal of gate driver 4 MOD I Control signal of gate driver 5 ...
Page 7
Pin No. Symbol I/O 40 − AGND 41 − AGND 42 REV I reverse control signal 43 COM O Produce REV signal with the amplitude of 44 − AGND 45 − AGND 46 − AGND 47 − AGND 48 − ...
Page 8
Table3 Pin No. Symbol I/O 1 VL1 I N.C ２ − 3 N.C − 4 VL2 I 5 N.C − 5-3)Touch panel driving section Table 4 Pin No. Symbol I − − ...
Page 9
A) TFT-LCD panel driving section Parameter Supply voltage for source driver (Analog) Supply voltage for source driver (Digital) Supply voltage High voltage for gate driver Low voltage Input voltage for Source driver (Low) Input voltage ...
Page 10
B0∼B5 terminals are applied. 【Note 7-2】DCLK,SPL,SPR,LBR,LP,REV,R0∼R5,G0∼G5 and B0∼B5 terminals are applied. 【Note 7-3】PS terminal is applied. 【Note 7-4】MOD,CLS,SPS and U/L terminals are applied. 【Note 7-5】VCOMAC should be alternated on VCOMDC every 1 horizontal period and 1 vertical ...
Page 11
Timing Characteristics of input signals Table 8 AC Characteristics (1) Parameter Clock frequency of source driver Rising time of clock Falling time of clock Pulse width (High level) Pulse width (Low level) Frequency of start pulse Setup time of ...
Page 12
DCLK 20% T wlp LP T susp T hsp T sulp SPL T wsp R0∼R5 G0∼G5 B0∼B5 T hcls CLS T sups PS VCOM 80% 80 240 20% T cwl T cwh T ...
Page 13
T rcls T whcls T wlcls 80% 80% CLS 1 2 20% 20% 20% T susps T hsps 80% 80% SPS 20% 20% T fsps T rsps R0∼R5 G0∼G5 Non-display period B0∼B5 T fcls 8 9 20% 1 ...
Page 14
Measurement condition : SPS=60Hz,CLS=15.73kHz,SPL=15.73kHz,DCLK=6.3MHz The term of PS=”Lo” in one horizontal period … 37μsec(234DCLK) Ta=25℃ Table 9 Parameter Sym Source Analog ISHA VSHA=+5.0V current Digital ISHD VSHD=+3.3V Gate High IDD current Low IEE 【Note 7-8】Vertical stripe pattern alternating ...
Page 15
Signals, Basic Display Color and Gray Scale of Each Color Table 10 Colors & Gray scale Gray Scale Black − Blue − Green − Cyan 0 0 ...
Page 16
Back light condition Table 11 Parameter Symbol θ21,22 Viewing angle θ11 range θ12 Contrast ratio CRmax τ r Response Rise τ d time Fall White chromaticity x y Reflection ratio R * The measuring method ...
Page 17
Back light condition Table 12 Parameter Symbol θ21,22 Viewing angle θ11 range θ12 Contrast ratio Crmax τ r Response Rise τ d time Fall White chromaticity x y Brightness Y LED life time LL * The measuring method ...
Page 18
Viewing angle range is defined as follows. θ θ ６o’clock direction Definition for viewing angle [Note 9-2] Definition of contrast ratio: The contrast ratio is defined as follows: Photodetecter output with all pixels white(GS63) ...
Page 19
A measurement device is Minolta CM-2002. [Note 9-5] Definition of reflection ratio Reflection ratio = [Note 9-6] A measurement device is ELDIM EZContrast [Note 9-7] This is the reference value. The White-LED life time is defind as a ...
Page 20
T/P should be supported from the backside of the glass. (2)Do not to use an adhensive-tape to bond it on the front of T/P and hang it to the housing ...
Page 21
Precautions 13-1) Insertion and taking out of FPCs Be sure insert and take out of the FPC into the connector of the set after turning off the power supply on the set side. 13-2) Handling of FPCs The FPC ...
Page 22
Test Conditions for TFT-LCD Module No. Test items High temperature storage test Ta=+70℃ Low temperature storage test 3 High temperature and high humidity operating test 4 High temperature test Low temperature operating test Tp=-10℃ Electro ...
Page 23
... The lot number is shown on a label. Attached location is shown in Fig.1 (Outline Dimensions). Indicated contents of the label LQ035Q7DB02R ○○○○○○○○ model No. 15-2) Used Regulation of Chemical Substances Breaking Ozone Stratum Substances with the object of regulating : CFCS, Carbon tetrachloride, Halon (a) This LCD module, Constructed part and Parts don’ ...
Page 24
LCP-05011−21 ...
Page 25
Fig.3 Forwarding Form LCP-05011−22 ...
Page 26
... ALL EXPRESS AND IMPLIED WARRANTIES, INCLUDING THE WARRANTIES OF MERCHANTABILITY, FITNESS FOR USE AND FITNESS FOR A PARTICULAR PURPOSE, ARE SPECIFICALLY EXCLUDED event will SHARP be liable any way responsible, for any incidental or consequential economic or property damage. NORTH AMERICA SHARP Microelectronics of the Americas 5700 NW Pacific Rim Blvd. Camas, WA 98607, U.S.A. Phone: (1) 360-834-2500 ...