MAX9702EVCMODU Maxim Integrated Products, MAX9702EVCMODU Datasheet - Page 2

• Manufacturer Part Number: MAX9702EVCMODU
• Description: Audio Modules & Development Tools 1.8W Filterless Ster eo Class D Audio Pow
• Manufacturer: Maxim Integrated Products

MAX9702 Evaluation System/Evaluation Kit
•
•
•
•
•
•
•
Do not turn on the power until all connections are
made.
1) On the CMODUSB command module, ensure the
2) For the MAX9702 EV kit, ensure the shunts are in
3) Carefully connect the boards by aligning the
Note: Indicate you are using the MAX9702 when contacting
the component supplier.
2
TDK
DESIGNATION
TP2, TP4–TP7,
TP11, TP12
SUPPLIER
_______________________________________________________________________________________
The MAX9702EVCMODU evaluation system
Power supply: +2.5V to +5.5V at 1.5A (V
Two audio sources, one stereo and one mono
Two 8Ω speakers
Stereo 16Ω headphone with 3.5mm plug
A user-supplied Windows 98SE/2000/XP PC
A spare USB port on the PC
shunt of J1 is in the position 2-3 (3.3V).
the default positions as follows.
MAX9702 EV kit’s 20-pin connector with the 20-pin
header of the CMODUSB command module. Gently
R2, R3
T1, T2
• MAX9702EVKIT
• CMODUSB command module (USB cable
R7
JU1: 1-2 (powered up).
JU2: 1-4 (SPP mode with f
JU3: 1-2 (enable headphone sensing).
included)
QTY
847-803-6100
0
1
0
0
PHONE
Component Suppliers
Recommended Equipment
Not installed, 1.5kΩ ±5% resistors
(0603)
49.9Ω ±1% resistor (0402)
Not installed, test points
Not installed, 50VDC, 1ADC, 800Ω
at 100MHz common-mode chokes
TDK ACM4532-801-2P
www.component.tdk.com
S
DESCRIPTION
= 1150kHz ±50kHz).
Quick Start
WEBSITE
Procedure
DD
)
4) Connect the right-channel speaker across the SR+
5) Connect the left-channel speaker across the SL+
6) Connect the right channel of the stereo audio
7) Connect the left channel of the stereo audio source
8) Connect the mono audio source output to INM.
9) Connect the positive terminal of the power supply to
10) Install the MAX9702 evaluation software on your
11) Connect the included USB cable from the PC to the
DESIGNATION
HELPFILE.HTM
MAX9702.EXE
INSTALL.EXE
FTD2XX.INF
press them together. The two boards should be
flush against each other.
and SR- test points.
and SL- test points.
source output to INR.
output to INL.
the VDD pad and the power-supply ground terminal
to the GND pad next to the VDD pad.
computer by running the INSTALL.EXE program on
the installation CD-ROM. The program files are
copied and icons are created for them in the
Windows Start Menu.
CMODUSB command module. A Building Driver
Database window should pop up in addition to a
New Hardware Found message. If a window simi-
lar to the one described above does not appear
after 30 seconds, then remove the USB cable from
the CMODUSB command module and reconnect it
again. Administrator privileges are required to install
the USB device driver on Windows 2000 and XP.
UNINST.INI
None
None
None
U1
FILE
Component List (continued)
QTY
Installs the EV kit files on your computer
Application program
Help file
USB device driver file
Uninstalls the EV kit software
1
3
1
1
MAX9702EV Kit Files
MAX9702ETI (28-pin TQFN)
Shunts
MAX9702 EV kit PC board
MAX9702 EV kit software
DESCRIPTION
DESCRIPTION