VNCLO-PSU-UK FTDI, Future Technology Devices International Ltd, VNCLO-PSU-UK Datasheet - Page 13

• Manufacturer Part Number: VNCLO-PSU-UK
• Description: POWER SUPPLY FOR VNCLO-MB1A UK
• Manufacturer: FTDI, Future Technology Devices International Ltd
• Series: Vinculor

Specifications of VNCLO-PSU-UK

• Accessory Type: Power Supply
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With/related Products: FTDI Vinculo Boards
• Other names: 768-1089

4
4.1 UART Interface
When the Vinco data and control buses are configured as a UART interface, the interface implements a
standard asynchronous serial UART port with flow control. The UART can support baud rates from
300baud to 6Mbaud. The UART interface is described in more detail in the Vinculum-II datasheet please
refer to: -
4.1.1 Signal Description – UART Interface
The UART signals can be programmed to a choice of available I/O pins. Table 4.1 explains the available
pins for each of the UART signals. This is a subset of what the VNC2-64Q is capable of to avoid conflict
with other functions on the Vinco module.
J2-1, J2-5, J3-2, J3-5, J4-6, J5-7, J6-1,
J6-5
J2-2, J2-6, J3-1, J3-6, J4-4, J5-1, J5-4,
J5-8, J6-2, J6-6
J1-1, J2-3, J3-3, J3-7, J4-1, J4-5, J5-2,
J5-5, J6-3, J6-7
J1-2, J2-4, J3-4, J3-8, J4-2, J4-3, J5-3,
J5-6, J6-4, J6-8
J2-1, J2-5, J3-2, J3-5, J4-6, J6,7, J6-1,
J6-5
J2-2, J2-6, J3-1, J3-6, J4-4, J5-1, J5-4,
J5-8, J6-2, J6-6
J1-1, J2-3, J3-3, J3-7, J4-1, J4-5, J5-2,
J5-5, J6-3, J6-7
J1-2, J2-4, J3-4, J3-8, J4-2, J4-3, J5-3,
J5-6, J6-4, J6-8
J2-1, J2-5, J3-2, J3-5, J4-6, J5-7, J6-1,
J6-5
Table 4.1 – Data and Control Bus Signal Mode Options – UART
Note: # defines active low signals.
Configurable Pin outs
Available Pins
FTDI website
Copyright © 2010-2011 Future Technology Devices International Limited
uart_tx_active
uart_dcd#
uart_dsr#
uart_cts#
uart_dtr#
uart_rts#
uart_ri#
uart_txd
uart_rxd
Name
Vinco Development Module Datasheet Version 2.0
Output
Output
Output
Output
Type
Input
Input
Input
Input
Input
Document Reference No.: FT_000327
Transmit asynchronous data output
(Default J3-2)
Receive asynchronous data input (Default
J3-1)
Request To Send Control Output
Clear To Send Control Input
Data Acknowledge (Data Terminal Ready
Control) Output
Data Request (Data Set Ready Control)
Input
Data Carrier Detect Control Input
Ring Indicator Control Input. RI# low can
be used to resume the PC USB Host
controller from suspend.
Enable Transmit Data for RS485 designs.
TXDEN
transmit operation is in progress. The
TXDEN signal will be set high one bit-time
before data is transmitted and return low
one bit time after the last bit of a data
frame has been transmitted
may be used to signal that a
Clearance No.: FTDI#173
Description
9