AD625AD Analog Devices Inc, AD625AD Datasheet - Page 8

• Manufacturer Part Number: AD625AD
• Description: Instrumentation Amplifier IC
• Manufacturer: Analog Devices Inc

Specifications of AD625AD

• Gain Max, V/v: 10000
• Input Offset Voltage Max: 200V
• Supply Voltage Max: 18V
• Mounting Type: Through Hole
• Supply Voltage Min: 6V
• Gain Min, V/v: 1
• Package / Case: 16-CDIP
• Rohs Status: RoHS non-compliant
• Amplifier Type: Instrumentation
• Number Of Circuits: 1
• Slew Rate: 5 V/µs
• Gain Bandwidth Product: 25MHz
• -3db Bandwidth: 650kHz
• Current - Input Bias: 30nA
• Voltage - Input Offset: 50µV
• Current - Supply: 3.5mA
• Voltage - Supply, Single/dual (±): ±6 V ~ 18 V
• Operating Temperature: -40°C ~ 85°C
• Output Type: -
• Current - Output / Channel: -

AD625
THEORY OF OPERATION
The AD625 is a monolithic instrumentation amplifier based on
a modification of the classic three-op-amp approach. Monolithic
construction and laser-wafer-trimming allow the tight matching
and tracking of circuit components. This insures the high level
of performance inherent in this circuit architecture.
A preamp section (Q1–Q4) provides additional gain to A1 and
A2. Feedback from the outputs of A1 and A2 forces the collec-
tor currents of Q1–Q4 to be constant, thereby, impressing the
input voltage across R
outputs of A1 and A2 which is given by the gain (2R
times the differential portion of the input voltage. The unity
gain subtracter, A3, removes any common-mode signal from the
output voltage yielding a single ended output, V
the potential at the reference pin.
The value of R
tance of the input preamp stage. As R
gains the transconductance increases. This has three important
advantages. First, this approach allows the circuit to achieve a
very high open-loop gain of (3 × 10
thus reducing gain related errors. Second, the gain-bandwidth
product, which is determined by C3, C4, and the input trans-
conductance, increases with gain, thereby, optimizing frequency
response. Third, the input voltage noise is reduced to a value
determined by the collector current of the input transistors
(4 nV/√Hz).
INPUT PROTECTION
Differential input amplifiers frequently encounter input voltages
outside of their linear range of operation. There are two consid-
erations when applying input protection for the AD625; 1) that
continuous input current must be limited to less than 10 mA
and 2) that input voltages must not exceed either supply by
more than one diode drop (approximately 0.6 V @ 25°C).
Under differential overload conditions there is (R
series with two diode drops (approximately 1.2 V) between the
plus and minus inputs, in either direction. With no external protec-
tion and R
voltage the AD625 can withstand, continuously, is approximately
± 2.5 V. Figure 26a shows the external components necessary to
protect the AD625 under all overload conditions at any gain.
–IN
50
G
50 A
very small (i.e., 40 Ω), the maximum overload
G
Q1, Q3
is the determining factor of the transconduc-
50 A
DRIVE
GAIN
C3
SENSE
GAIN
G
A1
. This creates a differential voltage at the
R
F
+V
+
–
–V
V
R
B
G
S
S
R
SENSE
GAIN
F
A2
GAIN
DRIVE
50 A
C4
Q2, Q4
8
at programmed gains ≥ 500)
G
50 A
is reduced for larger
10k
10k
50
OUT
10k
10k
+IN
G
, referred to
+ 100) Ω in
F
/R
SENSE
V
REF
G
O
+ 1)
The diodes to the supplies are only necessary if input voltages
outside of the range of the supplies are encountered. In higher
gain applications where differential voltages are small, back-to-
back Zener diodes and smaller resistors, as shown in Figure
26b, provides adequate protection. Figure 26c shows low cost
FETs with a maximum ON resistance of 300 Ω configured to offer
input protection with minimal degradation to noise, (5.2 nV/√Hz
compared to normal noise performance of 4 nV/√Hz).
During differential overload conditions, excess current will flow
through the gain sense lines (Pins 2 and 15). This will have no
effect in fixed gain applications. However, if the AD625 is being
used in an SPGA application with a CMOS multiplexer, this
current should be taken into consideration. The current capa-
bilities of the multiplexer may be the limiting factor in allowable
overflow current. The ON resistance of the switch should be
included as part of R
protection resistance.
+IN
–IN
+IN
–IN
+IN
–IN
500
500
1.4k
1.4k
2N5952
2N5952
1N5837A
1N5837A
FD333
2k
2k
FD333
FD333
G
when calculating the necessary input
FD333
FD333
FD333
FD333
FD333
FD333
FD333
R
R
R
R
R
R
R
R
R
G
G
G
F
F
F
F
F
F
FD333
FD333
AD625
AD625
AD625
–V
+V
–V
+V
–V
+V
S
S
S
S
S
S
V
V
V
OUT
OUT
OUT