AD7731BR-REEL Analog Devices Inc, AD7731BR-REEL Datasheet - Page 16

• Manufacturer Part Number: AD7731BR-REEL
• Description: IC,Data Acquisition Signal Conditioner,3-CHANNEL,24-BIT,SOP,24PIN,PLASTIC
• Manufacturer: Analog Devices Inc

Specifications of AD7731BR-REEL

• Rohs Status: RoHS non-compliant
• Number Of Bits: 24
• Sampling Rate (per Second): 6.4k
• Data Interface: DSP, Serial, SPI™
• Number Of Converters: 1
• Power Dissipation (max): 125mW
• Voltage Supply Source: Analog and Digital
• Operating Temperature: -40°C ~ 85°C
• Mounting Type: Surface Mount
• Package / Case: 24-SOIC (0.300", 7.50mm Width)
• For Use With: EVAL-AD7731EBZ - BOARD EVALUATION FOR AD7731

AD7731
MD2
0
0
0
0
1
1
1
1
MD1
0
0
1
1
0
0
1
1
MD0
0
1
0
1
0
1
0
1
Operating Mode
Sync (Idle) Mode. In this mode, the modulator and filter are held in reset mode and the AD7731 is not
processing any new samples or data. Placing the part in this mode is equivalent to exerting the SYNC
input pin. However, exerting the SYNC does not actually force these mode bits to 0, 0, 0. The part re-
turns to this mode after a calibration or after a conversion in Single Conversion Mode. This is the default
condition of these bits after Power-On/Reset.
Continuous Conversion Mode. In this mode, the AD7731 is continuously processing data and providing
conversion results to the Data Register at the programmed output update rate (as determined by the
Filter Register). For most applications, this would be the normal operating mode of the AD7731.
Single Conversion Mode. In this mode, the AD7731 performs a single conversion, updates the Data
Register, returns to the Sync Mode and resets the mode bits to 0, 0, 0. The result of the single conversion
on the AD7731 in this mode will not be provided until the full settling-time of the filter has elapsed.
Power-Down (Standby) Mode. In this mode, the AD7731 goes into its power-down or standby state. Placing
the part in this mode is equivalent to exerting the STANDBY input pin. However, exerting STANDBY does
not actually force these mode bits to 0, 1, 1.
Zero-Scale Self-Calibration Mode. This activates zero-scale self-calibration on the channel selected by the
CH2, CH1 and CH0 bits of the Mode Register. This zero-scale self-calibration is performed at the se-
lected gain on internally shorted (zeroed) inputs. When this zero-scale self-calibration is complete, the
part updates the contents of the Offset Calibration Register and returns to Sync Mode with MD2, MD1
and MD0 returning to 0, 0, 0. The RDY output and bit go high when calibration is initiated and return
low when this zero-scale self-calibration is complete to indicate that the part is back in Sync Mode and
ready for further operations.
Full-Scale Self-Calibration Mode. This activates full-scale self-calibration on the channel selected by the
CH2, CH1 and CH0 bits of the Mode Register. This full-scale self-calibration is performed at the se-
lected gain on an internally-generated full-scale signal. When this full-scale self-calibration is complete,
the part updates the contents of the Gain Calibration Register and returns to Sync Mode with MD2,
MD1 and MD0 returning to 0, 0, 0. The RDY output and bit go high when calibration is initiated and
return low when this full-scale self-calibration is complete to indicate that the part is back in Sync Mode
and ready for further operations.
Zero-Scale System Calibration Mode. This activates zero scale system calibration on the channel selected
by the CH2, CH1 and CH0 bits of the Mode Register. Calibration is performed at the selected gain on
the input voltage provided at the analog input during this calibration sequence. This input voltage should
remain stable for the duration of the calibration. When this zero-scale system calibration is complete, the
part updates the contents of the Offset Calibration Register and returns to Sync Mode with MD2, MD1
and MD0 returning to 0, 0, 0. The RDY output and bit go high when calibration is initiated and return
low when this zero-scale calibration is complete to indicate that the part is back in Sync Mode and ready
for further operations.
Full-Scale System Calibration Mode. This activates full-scale system calibration on the selected input
channel. Calibration is performed at the selected gain on the input voltage provided at the analog input
during this calibration sequence. This input voltage should remain stable for the duration of the calibra-
tion. When this full-scale system calibration is complete, the part updates the contents of the Gain Cali-
bration Register and returns to Sync Mode with MD2, MD1 and MD0 returning to 0, 0, 0. The RDY
output and bit go high when calibration is initiated and return low when this full-scale calibration is com-
plete to indicate that the part is back in Sync Mode and ready for further operations.
–16–
REV. A
REV. 0