AD7890AR-2 Analog Devices Inc, AD7890AR-2 Datasheet - Page 14

• Manufacturer Part Number: AD7890AR-2
• Description: A/D Converter (A-D) IC
• Manufacturer: Analog Devices Inc
• Type: Data Acquisition System (DAS)r

Specifications of AD7890AR-2

• No. Of Bits: 12 Bit
• No. Of Channels: 8
• Rohs Status: RoHS non-compliant
• Resolution (bits): 12 b
• Sampling Rate (per Second): 117k
• Data Interface: Serial
• Voltage Supply Source: Single Supply
• Voltage - Supply: 0 V ~ 2.5 V
• Operating Temperature: -40°C ~ 85°C
• Mounting Type: Surface Mount
• Package / Case: 24-SOIC (7.5mm Width)

DSCC FORM 2234
APR 97
MIL-PRF-38535 or as modified in the device manufacturer's Quality Management (QM) plan. The modification in the QM plan
shall not affect the form, fit, or function as described herein. For device class M, sampling and inspection procedures shall be
in accordance with MIL-PRF-38535, appendix A.
on all devices prior to qualification and technology conformance inspection. For device class M, screening shall be in
accordance with method 5004 of MIL-STD-883, and shall be conducted on all devices prior to quality conformance inspection.
accordance with MIL-PRF-38535. Inspections to be performed shall be those specified in MIL-PRF-38535 and herein for
groups A, B, C, D, and E inspections (see 4.4.1 through 4.4.4).
MIL-PRF-38535 including groups A, B, C, D, and E inspections and as specified herein. Quality conformance inspection for
device class M shall be in accordance with MIL-PRF-38535, appendix A and as specified herein. Inspections to be performed
for device class M shall be those specified in method 5005 of MIL-STD-883 and herein for groups A, B, C, D, and E inspections
(see 4.4.1 through 4.4.4).
4.4.2 Group C inspection. The group C inspection end-point electrical parameters shall be as specified in table II herein.
4. QUALITY ASSURANCE PROVISIONS
4.1 Sampling and inspection. For device classes Q and V, sampling and inspection procedures shall be in accordance with
4.2 Screening. For device classes Q and V, screening shall be in accordance with MIL-PRF-38535, and shall be conducted
4.2.1 Additional criteria for device class M.
4.2.2 Additional criteria for device classes Q and V.
4.3 Qualification inspection for device classes Q and V. Qualification inspection for device classes Q and V shall be in
4.4 Conformance inspection. Technology conformance inspection for classes Q and V shall be in accordance with
4.4.1 Group A inspection.
a.
b.
a.
b.
c.
a.
b.
c.
DEFENSE SUPPLY CENTER COLUMBUS
Burn-in test, method 1015 of MIL-STD-883.
(1) Test condition A, B, C, D, or E. The test circuit shall be maintained by the manufacturer under document revision
(2) T
Interim and final electrical test parameters shall be as specified in table II herein.
The burn-in test duration, test condition and test temperature, or approved alternatives shall be as specified in the
device manufacturer's QM plan in accordance with MIL-PRF-38535. The burn-in test circuit shall be maintained under
document revision level control of the device manufacturer's Technology Review Board (TRB) in accordance with
MIL-PRF-38535 and shall be made available to the acquiring or preparing activity upon request. The test circuit shall
specify the inputs, outputs, biases, and power dissipation, as applicable, in accordance with the intent specified in test
method 1015 of MIL-STD-883.
Interim and final electrical test parameters shall be as specified in table II herein.
Additional screening for device class V beyond the requirements of device class Q shall be as specified in
MIL-PRF-38535, appendix B.
Tests shall be as specified in table II herein.
Subgroups 4, 5, 6, 7, and 8 in table I, method 5005 of MIL-STD-883 shall be omitted.
Subgroups 9, 10, 11 are tested initially and after any design changes which may affect the parameters in those
subgroups.
MICROCIRCUIT DRAWING
level control and shall be made available to the preparing or acquiring activity upon request. The test circuit shall
specify the inputs, outputs, biases, and power dissipation, as applicable, in accordance with the intent specified in
test method 1015.
COLUMBUS, OHIO 43216-5000
A
= +125 C, minimum.
STANDARD
SIZE
A
REVISION LEVEL
C
SHEET
5962-95615
14