ADUC843BCP32Z-5 Analog Devices Inc, ADUC843BCP32Z-5 Datasheet - Page 48

• Manufacturer Part Number: ADUC843BCP32Z-5
• Description: Microconverter, ADUC842 Without DACs
• Manufacturer: Analog Devices Inc
• Series: MicroConverter® ADuC8xxr

Specifications of ADUC843BCP32Z-5

• Core Processor: 8052
• Core Size: 8-Bit
• Speed: 16.78MHz
• Connectivity: I²C, SPI, UART/USART
• Peripherals: DMA, PSM, PWM, Temp Sensor, WDT
• Number Of I /o: 32
• Program Memory Size: 32KB (32K x 8)
• Program Memory Type: FLASH
• Ram Size: 2.25K x 8
• Voltage - Supply (vcc/vdd): 4.75 V ~ 5.25 V
• Data Converters: A/D 8x12b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 56-LFCSP
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

ADuC841/ADuC842/ADuC843
I
The ADuC841/ADuC842/ADuC843 support a fully licensed
I
hardware slave and software master. SDATA is the data I/O pin,
and SCLOCK is the serial clock. These two pins are shared with
the MOSI and SCLOCK pins of the on-chip SPI interface. To
enable the I
(see SPE in Table 18) or the SPI interface must be moved to
P3.3, P3.4, and P3.5 via the CFG841.1/CFG842.1 bit. Application
Note uC001 describes the operation of this interface as imple-
mented and is available from the MicroConverter website at
www.analog.com/microconverter.
Table 19. I2CCON SFR Bit Designations, Master Mode
Bit No.
7
6
5
4
3
2
1
0
Table 20. I2CCON SFR Bit Designations, Slave Mode
Bit No.
7
6
5
4
3
2
2
C serial interface. The I
C COMPATIBLE INTERFACE
Name
MDO
MDE
MCO
MDI
I2CM
----
----
----
Name
I2CSI
I2CGC
I2CID1
I2CID0
I2CM
2
C interface, the SPI interface must be turned off
Description
I
This data bit is used to implement a master I
the SDATA pin if the data output enable (MDE) bit is set.
I
Set by the user to enable the SDATA pin as an output (Tx).
Cleared by the user to enable the SDATA pin as an input (Rx).
I
This data bit is used to implement a master I
the SCLOCK pin.
I
This data bit is used to implement a master I
this bit on SCLOCK if the data output enable (MDE) bit is 0.
I
Set by the user to enable I
Cleared by the user to enable I
Reserved.
Reserved.
Reserved.
Description
I
Set by the user to enable I
interrupt.
Cleared by the user to disable I
I
Set by hardware after receiving a general call address.
Cleared by the user.
I
Set by hardware to indicate the source of an I
00 Start and Matching Address.
01 Repeated Start and Matching Address.
10 User Data.
11 Stop after a Start and Matching Address.
I
Set by the user to enable I
Cleared by the user to enable I
2
2
2
2
2
2
2
2
2
C Software Master Data Output Bit (Master Mode Only).
C Software Master Data Output Enable Bit (Master Mode Only).
C Software Master Clock Output Bit (Master Mode Only).
C Software Master Data Input Bit (Master Mode Only).
C Master/Slave Mode Bit.
C Stop Interrupt Enable Bit.
C General Call Status Bit.
C Interrupt Decode Bits.
C Master/Slave Mode Bit.
2
C interface is implemented as a full
2
2
2
C software master mode.
C stop interrupts. If set, a stop bit that follows a valid start condition generates an
C software master mode.
2
2
2
C hardware slave mode.
C hardware slave mode.
C stop interrupts.
Rev. 0 | Page 48 of 88
2
2
2
C transmitter interface in software. Data written to this bit is output on
C transmitter interface in software. Data written to this bit is output on
C receiver interface in software. Data on the SDATA pin is latched into
2
C interrupt.
Three SFRs are used to control the I
described in the following tables.
I2CCON
SFR Address
Power-On Default
Bit Addressable
I
E8H
00H
Yes
2
C Control Register
2
C interface and are