CS4299-JQZR Cirrus Logic Inc, CS4299-JQZR Datasheet - Page 36

• Manufacturer Part Number: CS4299-JQZR
• Description: IC AC97 Codec With SRC
• Manufacturer: Cirrus Logic Inc
• Series: SoundFusion™r
• Type: Audio Codec '97r

Specifications of CS4299-JQZR

• Data Interface: Serial
• Resolution (bits): 18 b, 20 b
• Number Of Adcs / Dacs: 1 / 1
• Sigma Delta: Yes
• Dynamic Range, Adcs / Dacs (db) Typ: 85 / 87
• Voltage - Supply, Analog: 4.75 V ~ 5.25 V
• Voltage - Supply, Digital: 3.3 V ~ 5 V
• Operating Temperature: 0°C ~ 70°C
• Mounting Type: Surface Mount
• Package / Case: 48-LQFP
• No. Of Dacs: 1
• No. Of Input Channels: 6
• No. Of Output Channels: 2
• Adc / Dac Resolution: 20bit
• Adcs / Dacs Signal To Noise Ratio: 70dB
• Sampling Rate: 48kSPS
• Supply Voltage Range: 3.135V To 3.465V, 4.75V To 5.25V
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

6. ANALOG HARDWARE
The analog line-level input hardware consists of
four stereo inputs (LINE_IN_L/R, CD_L/GND/R,
VIDEO_L/R, and AUX_L/R), two selectable
mono microphone inputs (MIC1 and MIC2), and
two mono inputs (PC_BEEP and PHONE). The an-
alog line-level output hardware consists of a mono
output (MONO_OUT), and dual stereo line outputs
(LINE_OUT_L/R and ALT_LINE_OUT_L/R).
This section describes the analog hardware needed
to interface with these pins. The designs presented
in this section comply with specifications detailed
in Chapter 17 of the Microsoft
lines [7] (referred to as PC 99). For EMI reduction
techniques refer to the application note N165:
CS4297A/CS4299 EMI Reduction Techniques [5].
6.1
All analog inputs to the CS4299, including
CD_GND, should be capacitively coupled to the
input pins. Unused analog inputs should be tied to-
gether and connected through a capacitor to analog
ground or tied to the Vrefout pin directly. The max-
imum allowed voltage for analog inputs, except the
microphone input, is 1 V
input the maximum allowed voltage depends on the
selected boost setting.
6.1.1
Figure 10 shows circuitry for a line-level stereo in-
put. Replicate this circuit for the Line, Video and
Aux inputs. This design attenuates the input by
6 dB, bringing the signal from the PC 99 specified
2 V
6.1.2
The CD line-level input has an extra pin,
CD_GND, providing a pseudo-differential input
for both CD_L and CD_R. This pin takes the
common-mode noise out of the CD inputs when
36
36
RMS
DESCRIPTION
, to the CS4299 maximum allowed 1 V
Analog Inputs
Line-Level Inputs
CD Input
RMS
. For the microphone

PC Design Guide-
RMS
.
connected to the CD analog source ground. Follow-
ing the reference designs in Figure 11 and
Figure 12 provides extra attenuation of common
mode noise coming from the CD-ROM drive,
thereby producing a higher quality signal. One per-
cent resistors are recommended since closely
matched resistor values provide better com-
mon-mode attenuation of unwanted signals. The
circuit shown in Figure 11 can be used to attenuate
a 2 V
shown in Figure 12 can be used for a 1 V
put signal.
CD_COM
CD_COM
Figure 10. Line Input (Replicate for Video and Aux)
CD_R
CD_R
CD_L
CD_L
RMS
(All resistors 1%)
Figure 11. Differential 2 V
Figure 12. Differential 1 V
CD input signal by 6 dB. The circuit
6.8 kΩ
6.8 kΩ
3.4 kΩ
100 Ω
100 Ω
100 Ω
6.8 kΩ
6.8 kΩ
6.8 kΩ
47 kΩ
6.8 kΩ
6.8 kΩ
47 kΩ
AGND
AGND
3.4 kΩ
1.0 µ F
1.0 µF
47 kΩ
1.0 µF
RMS
RMS
1.0 µ F
1.0 µ F
1.0 µF
6.8 kΩ
CD Input
CD Input
2.2 µF
2.2 µF
CS4299
RMS
CS4299
DS319PP6
R
L
CD_R
CD_L
CD_GND
CD_R
CD_L
CD_GND
CD in-