ATV32HU40N4 SQUARE D, ATV32HU40N4 Datasheet - Page 2

• Manufacturer Part Number: ATV32HU40N4
• Description: ATV32 5 HP 480V 3 PHASE
• Manufacturer: SQUARE D

Local signalling
Output voltage
Insulation
Electrical connection
Tightening torque
Supply
Analogue input number
Analogue input type
Sampling duration
Response time
Accuracy
Linearity error
Analogue output number
Analogue output type
Discrete output number
Discrete output type
Minimum switching current
Maximum switching current
Discrete input number
Discrete input type
Discrete input logic
Acceleration and deceleration ramps
Braking to standstill
Protection type
2
1 LED red presence of drive voltage
1 LED blue presence of bluetooth
1 LED green presence of CANopen run
1 LED red presence of CANopen error
1 LED red presence of drive fault
<= power supply voltage
Electrical between power and control
Control screw terminal 0.5...1.5 mm² / AWG18...AWG14
Motor/Braking resistor removable screw terminals 1.5...2.5 mm² /
AWG14...AWG12
Power supply screw terminal 2.5...4 mm² / AWG12...AWG10
Control 0.5 N.m / 4.4 lb/ft
Motor/Braking resistor 0.7 N.m / 7.1 lb/ft
Power supply 0.6 N.m / 5.3 lb/ft
Internal supply for reference potentiometer (1 to 10 kOhm), 10.5 V DC +/- 5 % ,
<= 10 mA for overload and short-circuit protection
3
AI1 voltage 0...10 V DC , impedance 30000 Ohm, resolution 10 bits
AI2 bipolar differential voltage +/- 10 V DC , impedance 30000 Ohm, resolution
10 bits
AI3 current 0...20 mA (or 4-20 mA, x-20 mA, 20-x mA or other patterns by config-
uration) , impedance 250 Ohm, resolution 10 bits
AI1, AI2, AI3 2 ms for analog input(s)
AO1 2 ms for analog input(s)
LI1...LI6 8 ms, tolerance +/- 0.7 ms for logic output(s)
R1A, R1B, R1C 2 ms for relay output(s)
R2A, R2C 2 ms for relay output(s)
AI1, AI2, AI3 +/- 0.2 % for a temperature of -10...60 °C
AI1, AI2, AI3 +/- 0.5 % for a temperature of 25 °C
AO1 +/- 1 % for a temperature of 25 °C
AO1 +/- 2 % for a temperature of -10...60 °C
AI1, AI2, AI3 +/- 0.2...0.5 % of maximum value
AO1 +/- 0.3 %
1
AO1 software-configurable current 0...20 mA , impedance 800 Ohm, resolution
10 bits
AO1 software-configurable voltage 0...10 V , impedance 470 Ohm, resolution 10
bits
3
R1A, R1B, R1C configurable relay logic NO/NC, electrical durability 100000 cy-
cles
R2A, R2B configurable relay logic NO, electrical durability 100000 cycles
LO logic
Configurable relay logic 5 mA at 24 V DC
R1 on resistive load, 3 A at 250 V AC,
R1 on resistive load, 4 A at 30 V DC,
R1, R2 on inductive load, 2 A at 250 V AC,
R1, R2 on inductive load, 2 A at 30 V DC,
R2 on resistive load, 5 A at 250 V AC,
R2 on resistive load, 5 A at 30 V DC,
7
LI1...LI4 programmable (sink/source) 24...30 V DC , with level 1 PLC
LI5 programmable as pulse input 20 kpps 24...30 V DC , with level 1 PLC
LI6 switch-configurable PTC probe 24...30 V DC
STO safe torque off 24...30 V DC , impedance 1500 Ohm
LI1...LI6 negative logic (sink), > 19 V (state 0), < 13 V (state 0)
LI1...LI6 positive logic (source), < 5 V (state 0), > 11 V (state 0)
S
U
CUS
Deceleration ramp automatic stop DC injection
Deceleration ramp adaptation
Linear
Ramp switching
By DC injection
Input phase breaks drive
Overcurrent between output phases and earth drive
Overheating protection drive
Short-circuit between motor phases drive
Thermal protection drive