HS1B-114R-G IDEC, HS1B-114R-G Datasheet
HS1B-114R-G
Related parts for HS1B-114R-G
HS1B-114R-G Summary of contents
Page 1
... GS-ET-15 BG standard in Germany Direct Opening Action Part Numbers Pilot Light Part Number Without HS1B-11R With red LED HS1B-114R-R With green LED HS1B-114R-G Without HS1B-02R With red LED HS1B-024R-R With green LED HS1B-024R-G Description USA: 800-262-IDEC Canada: 888-317-IDEC HS1B Series Part Number Key ...
Page 2
... HS1B Series Specifi cations Conforming to Standards IEC60947-5-1, EN60947-5-1, GS-ET-15, UL508 Operating Temperature –25 to +70˚C (no freezing) Storage Temperature –40 to +80˚C Operating Humidity 85% RH maximum (no condensation) Altitude 2,000m maximum Rated Insulation Voltage (Ui) 300V (between LED and ground: 60V) Impulse Withstand Voltage (Uimp (between LED and ground: 2.5 kV) Between live and dead metal parts: 100 MΩ ...
Page 3
... Main Circuit: used to enable the machine to start only when the main circuit is closed. Auxiliary Circuit: used to indicate whether the main circuit or door is open or closed. 2. Terminals + and - are used for the LED indicator, and are isolated from door status. Wire the terminals only when needed. USA: 800-262-IDEC Canada: 888-317-IDEC HS1B Series Status ...
Page 4
... Actuator Angle Adjustment • Using the screw (M3 hex socket head screw), the actuator angle can be adjusted (refer to the dimensional drawing). Adjustable angle: (0˚) to 20˚ 364 Dimensions (mm) HS1B - using the Right-angle actuator (HS9Z-A2) (Horizontal Mounting) Conduit Port G1/2 Actuator Actuator Cover ...
Page 5
... Door Hinge HS2B Precautions • Cracks or burrs on the conduit entry may deteriorate the housing protection against water. • When changing to another conduit port, close the unused opening with an optional plug (Part No. HS9Z-P1). USA: 800-262-IDEC Canada: 888-317-IDEC Precautions Door Hinge Door Hinge 397 ...
Page 6
... The safety switch cover can be only removed with the special key wrench supplied with the switch or with the optional screwdriver (also applicable to HS1B and HS1E). • Remove the screw located on the unlocking entry at the side of the switch us- ing the key wrench included with the switch. Then insert a small screwdriver into the switch to push the lever inside of the switch toward the indicator until the actuator is unlocked (refer to the diagram on the right) ...
Page 7
... HS1C: 5.0±0.5 N-m (approx. 50±5 kgf-cm pcs of M5 hex socket head cap screws) ø4.1 min. • HS1B: 5.0±0.5 N-m (approx. 50±5 kgf-cm pcs hex socket head cap screws) Crimping Terminal 2 • HS2B: 5.0±0.5 N-m (approx. 50±5 kgf-cm) (2 pcs of M5 hex socket head cap screws) • ...
Page 8
... K-MECS) and a gasket (Part No.: GP M20, K-MECS). Install a gasket between the interlock switch and the adapter. Apply sealing tape between the cable gland and the adapter to make sure of IP67 protection for the enclosure. www.idec.com Door Interlock Switches Door Hinge Door Hinge ...