CSTCE8M00G52-B0 Murata, CSTCE8M00G52-B0 Datasheet - Page 10

• Manufacturer Part Number: CSTCE8M00G52-B0
• Manufacturer: Murata

Specifications of CSTCE8M00G52-B0

• Lead Free Status / RoHS Status: Compliant

!Note
• This PDF catalog is downloaded from the website of Murata Manufacturing co., ltd. Therefore, it’s specifications are subject to change or our products in it may be discontinued without advance notice. Please check with our
• This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
sales representatives or product engineers before ordering.
!Note
1. Soldering Conditions
(1) Reflow
2. Wash
(1) Cleaning Solvents
(2) Temperature Difference : dT *1
(4) Drying
3. Notice for Mounting
(2) Soldering Iron
(3) Conditions
(5) Others
CSTCC/CSTCR/CSTCE_V/CSTCE_G/CSTCV/CSACV Series
One heat stress, shown in the profile at right, is applied to
resonator, then after being placed in natural conditions
for 1 hour, the resonator is measured.
(a) Pre-heating conditions should be +150 to +180 C for
(b) Heating conditions should be within 40 seconds at
HCFC, Isopropanol, Tap water, Demineralized water,
Cleanthrough750H, Pine alpha 100S, Techno care FRW
dT<=60 C (dT=Component-solvent)
*1 ex. In case the component at +90 C immerses into
5 minutes max. by air blow at +80 C max.
(a) Total washing time should be within 10 minutes.
(b) The component may be damaged if it is washed with
(a) The component is recommended for use with
Components shall be measured after soldering on PCB
at +350 5 C for 3.0 0.5 seconds and leaving in natural
condition for 24 hours. The soldering iron shall not touch
the components while soldering.
(a) Ultrasonic Wash
• Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
1 minute max. in above solvent at +60 C max.
60 to 120 seconds. Ascending time up to +150 C
should be longer than 30 seconds.
+230 C min., but peak temperature should be Iower
than +260 C.
(Frequency: 28kHz, Output: 20W/l)
chlorine, petroleum, or alkali cleaning solvent.
placement machines which employ optical placement
capabilities. The component might be damaged by
excessive mechanical force. Please make sure to
evaluate by using placement machines before going
into mass production. Do not use placement
machines which utilize mechanical positioning. Please
contact Murata for details beforehand.
cleaning solvent at +60 C, then dT=30 C.
MHz Chip Type Notice (Soldering and Mounting) for Automotive
(b) Immersion Wash
(c) Shower or Rinse Wash
(b) Please insure the component is thoroughly evaluated
(c) Please do not apply excess mechanical stress to the
5 minutes max. in above solvent at +60 C max.
5 minutes max. in above solvent at +60 C max.
in your application circuit.
component and terminals during soldering.
230
180
150
30 sec.
min.
(150-180˚C)
Pre-heating
60-120 sec.
(260˚C max.)
Heating
(230˚C)
40 sec.
Peak
max.
Gradual
Cooling
120 sec.
min.
13
P16E.pdf
09.5.20
2