CS4205-KQ Cirrus Logic Inc, CS4205-KQ Datasheet - Page 64

• Manufacturer Part Number: CS4205-KQ
• Description: Audio CODECs IC AC'97 Codec for Docking Stations
• Manufacturer: Cirrus Logic Inc

Specifications of CS4205-KQ

• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

12. ANALOG HARDWARE
The analog input section consists of four stereo
line-level inputs (LINE_L/R, CD_L/GND/R,
VIDEO_L/R, and AUX_L/R), two selectable
mono microphone inputs (MIC1 and MIC2), and
two mono inputs (PC_BEEP and PHONE). The an-
alog output section consists of a mono output
(MONO_OUT) and a stereo line-level output
(LINE_OUT_L/R). This section describes the ana-
log hardware needed to interface with these pins.
The designs presented in this section are compliant
with Chapter 17 of Microsoft’s
sign Guide [7] (referred to as PC 99) and Chapter
11 of Microsoft’s
[8] (referred to as PC 2001). For information on
EMI reduction techniques refer to the application
note AN165: CS4297A/CS4299 EMI Reduction
Techniques [5].
12.1 Analog Inputs
All analog inputs to the CS4205, including
CD_GND, should be capacitively coupled to the
input pins. Unused analog inputs should be tied to-
gether and connected through a capacitor to analog
ground or tied to the Vrefout pin directly. The max-
imum allowed voltage for analog inputs, except the
microphone input, is 1 V
lowed voltage for the microphone input depends on
the selected boost setting.
12.1.1 Line Inputs
Figure 25 shows circuitry for a line-level stereo in-
put. Replicate this circuit for the Video and Aux in-
puts. This design attenuates the input by 6 dB,
bringing the signal from the PC 99 specified
2 V
12.1.2 CD Input
The CD line-level input has an extra pin,
CD_GND, providing a pseudo-differential input
for both CD_L and CD_R. This pin takes the
64
RMS
DESCRIPTION
, to the CS4205 maximum allowed 1 V
®
PC 2001 System Design Guide
RMS
. The maximum al-
®
PC 99 System De-
RMS
.
common-mode noise out of the CD inputs when
connected to the CD analog source ground. Follow-
ing the reference designs in Figure 26 and
Figure 27 provides extra attenuation of common
mode noise coming from the CD-ROM drive,
thereby producing a higher quality signal. One per-
cent resistors are recommended since closely
matched resistor values provide better com-
mon-mode attenuation of unwanted signals. The
circuit shown in Figure 26 can be used to attenuate
a 2 V
shown in Figure 27 can be used for a 1 V
input signal.
CD_COM
CD_COM
Figure 25. Line Input (Replicate for Video and AUX)
CD_R
CD_L
CD_R
CD_L
RMS
(All resistors 1%)
Figure 26. Differential 2 V
Figure 27. Differential 1 V
AGND
CD input signal by 6 dB. The circuit
100 Ω
100 Ω
100 Ω
6.8 kΩ
6.8 kΩ
3.4 kΩ
6.8 kΩ
6.8 kΩ
6.8 kΩ
47 kΩ
6.8 kΩ
47 kΩ
6.8 kΩ
AGND
AGND
AGND
1.0 µF
47 kΩ
3.4 kΩ
1.0 µ F
1.0 µ F
6.8 kΩ
1.0 µF
RMS
RMS
1.0 µ F
1.0 µ F
2.2 µF
CD Input
CD Input
2.2 µ F
LINE_IN_R
LINE_IN_L
CS4205
DS489PP4
CD_R
CD_L
CD_GND
RMS
CD_R
CD_L
CD_GND
CD