BFC233844104 Vishay, BFC233844104 Datasheet - Page 11

• Manufacturer Part Number: BFC233844104
• Description: Cap Film 0.1uF 300VAC PP 20% 17.5 X 6 X 12mm RDL 15mm Loose in Box
• Manufacturer: Vishay

Specifications of BFC233844104

• Package/case: 17.5(Max) X 6(Max) X 12(Max)
• Mounting: Through Hole
• Capacitance Value: 0.1 uF
• Voltage: 300 Vac
• Dielectric: PP
• Lead Pitch For Radial: 15 mm
• Product Length: 17.5(Max) mm
• Product Depth: 6(Max) mm
• Tolerance: 20 %
• Operating Temperature: -55 to 105 °C

Document Number: 28118
Revision: 22-Dec-10
SUB-CLAUSE NUMBER
AND TEST
SUB-GROUP C2
4.12
4.12.1 Initial measurements
4.12.3 Final measurements
SUB-GROUP C3
4.13.1 Initial measurements
4.13
4.14
4.14.7 Final measurements
Damp heat steady state
Impulse voltage
Endurance
Interference Suppression Film Capacitors
CONDITIONS
56 days, 40 °C, 90 to 95 % RH
No load
Capacitance
Tangent of loss angle at 1 kHz
Visual examination
Capacitance
Tangent of loss angle
Voltage proof
Insulation resistance
Capacitance
Tangent of loss angle:
For C ≤ 1 µF at 10 kHz
For C > 1 µF at 1 kHz
3 successive impulses, full wave, peak
voltage:
X2: 2.5 kV for C ≤ 1 µF
X2: 2.5 kV for C >1 µF
Max. 24 pulses
Duration: 1000 h
1.25 x U
Once in every hour the voltage is increased
to 1000 V
47 Ω ± 5 %
Visual examination
Capacitance
Tangent of loss angle
Voltage proof
Insulation resistance
For technical questions, contact:
1290 V
1320 V
1 min between terminals
1290 V
1320 V
1 min between terminals
2200 V
terminals and case
RAC
RMS
AC;
DC
DC
DC
DC
at 105 °C
; pitch ≤ 27.5 mm
; pitch > 27.5 mm
for 0.1 s via resistor of
; pitch ≤ 27.5 mm
; pitch > 27.5 mm
1 min between
[e-mail]
PERFORMANCE REQUIREMENTS
No visible damage
Legible marking
|ΔC/C| ≤ 5 % of the value measured in
4.12.1.
Increase of tan δ:
≤ 0.008 for : C ≤ 1 µF or
≤ 0.005 for : C > 1 µF
Compared to values measured in 4.12.1
No permanent breakdown or flash-over
≥ 50 % of values specified in section
“Insulation resistance” of this specification
No self healing breakdowns or flash-over
No visible damage
Legible marking
|ΔC/C| ≤ 10 % compared to values
measured in 4.13.1.
Increase of tan δ:
≤ 0.008 for : C ≤ 1 µF or
≤ 0.005 for : C > 1 µF
Compared to values measured in 4.13.1
No permanent breakdown or flash-over
≥ 50 % of values specified in chapters
“General data” of this specification
MKP338 4 X2
www.vishay.com
Vishay
11