S19233PRIB AMCC, S19233PRIB Datasheet - Page 31

• Manufacturer Part Number: S19233PRIB
• Description: Ethernet/Fibre Channel 49-Pin BGA
• Manufacturer: AMCC

Specifications of S19233PRIB

• Package: 49BGA
• Maximum Data Rate: 11.32 Gbps
• Transmission Media Type: Wire
• Power Supply Type: Analog
• Typical Supply Current: 380 mA
• Typical Operating Supply Voltage: 1.8|3.3 V
• Minimum Operating Supply Voltage: 1.65|3.03 V
• Maximum Operating Supply Voltage: 1.95|3.56 V

S19233 – 10 G Ethernet/Fibre Channel/SONET/SDH
Dual CDR
ELECTRICAL CHARACTERISTICS
Table 14. Absolute Maximum Stress Ratings
The following are the absolute maximum stress ratings for the S19233 device. Stresses beyond those listed may cause permanent damage to the device. Absolute
maximum ratings are stress ratings only, and operation of the device at the maximums stated, or any other conditions beyond those indicated in the “Recommended
Operating Conditions” of the document, are not inferred. Exposure to absolute maximum rating conditions will affect device reliability.
Table 15. Recommended Operating Conditions
The device will meet all electrical specifications at a junction temperature under bias of 125C but part lifetime and reliability may be reduced. It is recommended that
prudent thermal management techniques are used to maximize device lifetime.
AMCC Confidential and Proprietary
Storage Temperature Range
1.8 V Supply
3.3 V Supply
Voltage on High Speed CML Input Pin
Voltage on Low Speed CML Input Pin
Voltage on any LVCMOS Input Pin
Voltage on any LVTTL Input Pin
LVTTL Output Sink Current
LVTTL Output Source Current
Electrostatic Discharge (ESD) Sensitivity Rating - Human Body Model (HBM):
The S19233 is rated to the following ESD voltages based upon JEDEC standard: JESD22-A114-B
1. CLASS 1C- All pins are rated at or above 1500 volts except high speed I/O pins which are only rated to 1000 volts.
Adherence to standards for ESD protection should be taken during the handling of the devices to ensure that the devices are not damaged. The standards to be
used are defined in ANSI standard ANSI/ESD S20.20-1999, "Protection of Electrical and Electronic Parts, Assemblies and Equipment." Contact your local FAE
or sales representative for applicable ESD application notes.
Ambient Temp under Bias
Junction Temp under Bias
Voltage on 1.8 V Supply
Current on 1.8 V Supply
Voltage on 3.3 V Supply
Current on 3.3 V Supply
Power
Power Supply Noise Rejection
Parameter
Parameter
3.135
Min.
1.71
-40
Symbol
V
V
T
DD_1.8
DD_3.3
STG
1.80
Typ
380
740
3.3
3.465
+125
Max.
1.89
+85
425
820
Min.
1.65
3.03
36
54
66
99
-55
7
Units
mV
mV
mV
mV
V
V
mW
mA
mA
°C
°C
V
V
DD_3.3
DD_3.3
pp
pp
pp
pp
Max.
+150
2400
1600
1.95
3.56
3
4
+0.5
+0.3
Industrial Temp. Range
(± 5%) wrt GND
(± 5%) wrt GND
Typical supply voltages. Max power of
650 mW with LOS turned off.
1.8V supply (50 KHz - 1 MHz)
1.8V supply (1 MHz - 10 MHz)
3.3V supply (50 KHz - 1 MHz)
3.3V supply (1 MHz - 10 MHz)
Revision 5.00 – March 16, 2007
Units
mV
mV
mA
mA
°C
V
V
V
V
Conditions
Differential
Differential
Data Sheet
Conditions
31