0248500000 Weidmuller, 0248500000 Datasheet - Page 6

• Manufacturer Part Number: 0248500000
• Manufacturer: Weidmuller
• Type: Connecting Sleever

TSTW mounting rail supports allow for sloped fitting of mount-
ing rails at an angle of 35°. Three designs are available with M5,
M6 threads or with a bore of Ø 4.3 mm.
The TST mounting rail support allows rails to be fitted into fram-
es or above a cut-out. This design has an M5 or M6 thread (not
shown).
Weidmüller offers hexagon socket fixing screws for the mount-
ing rail supports with a particularly low head allowing terminals
also to be fitted above the screw.
TSTW (M 5)
TSTW (M 6)
TSTW ø 4.3
TST (M 6)
TST (M 5)
TSTW (M 5), zinc-plated
FKSC M 5x8 ø 9 hexagon socket SW 2.5
FKSC M 6x8 ø 9 hexagon socket SW 3
FKSC M 6x12 ø 9 hexagon socket SW 3
TSTW, TST
Material thickness 1.8 mm
TSTW
TSTW
TST
Type
Fixing screw
Mounting rail support
Cat. No.
Qty.
0178100000 10
0164000000 10
1610110000 10
0101700000 10
1286600000 10
1779100000 10
0295900000 50
0642600000 50
0353500000 50
SH 1 for TS 15
in PA (thermoplastics) compl.
SH 1 Base
SH 1 Bracket
SH 2 for TS 32/35
in KrG (thermosetting)
Support block for TS 15, TS 32, TS 35
and busbars
SH 1
for TS 15
SH 2
for TS 32, TS 35
The SH 1 and SH 2 support blocks enable construction of insu-
lated mounting rails.
Type
Type
Support block
Cat. No.
0299860000
0401460000
0635960000
Cat. No.
0494920000
SH 2
Qty.
Qty.
500
20
20
10
FM 4 (M 4) for TS 35
FM 5 (M 5) for TS 35
FM 6 (M 6) for TS 35
FM (Ø 4.2) for TS 35
MOFU mounting foot PA orange 0646260000 with bore
for TS 35 x 7.5 u. 35 x 15 gel.
MB 3/5 (cream)
with thread M 3 and M 5, for TS 32
MB 6/4 (grey)
with thread M 6 and M 4, for TS 32
MB 5/3 (black)
with thread M 5 and M 3, for TS 32
Mounting bases for TS 32 and TS 35
MOFU
FM
MB
Mounting bases are used to fix components onto mounting
rails. Weidmüller offers a polyamide mounting base and a steel
snap-on base for the TS 35 mounting rail. The FM 4 snap on
base fits all “top-hat” mounting rails. The PA mounting base fits
the TS 35 x 7.5 and the TS 35 x 15 slotted rails.
The sliding nut for TS 32 mounting rails has 2 tapped holes for
M 3 + M 5 / M 6 + M 4 / M 5 + M 3 screws. It is used to fix
components which cannot be directly mounted on the TS 32
and, in particular, to accept the smaller TS 15 “top-hat” rail. In
this way, for example, small terminals can first be mounted on
the TS 15 and this rail can then be mounted on the TS 32 with
the aid of the sliding nut together with the terminals.
Type
Mounting bases
Cat. No.
Qty.
0687900000
0636800000
0636900000
1724580000
0495660000 without bore
0503500000
0334900000
0553400000
261
40
40
40
40
20
20
20
20
20