NFS110-7601PJ ARTESYN, NFS110-7601PJ Datasheet - Page 4

• Manufacturer Part Number: NFS110-7601PJ
• Description: AC/DC Power Supply Quad-OUT 5.1V/12V/-12V/-5V 8A/4.5A/0.5A/0.5A 110W 15-Pin
• Manufacturer: ARTESYN

Specifications of NFS110-7601PJ

• Input Voltage: 85 to 264 V
• Output Voltage: 5.1|12|-12|-5 V
• Maximum Output Current: 8|4.5|0.5|0.5 A
• Number Of Outputs: 4
• Maximum Output Power: 110 W
• Efficiency: 70(Typ) %
• Input Frequency: 47 to 440 Hz
• Operating Temperature: 0 to 70 °C

0.050 0.020
AC (J1) mating connector
Molex 09-50-3051 or Molex 09-91-0500 mating connector with 2478
or equivalent crimp terminals.
DC (J2) mating connector
Mechanical Notes:
A Metallic or non-metallic stand-offs (maximum diameter 5.4mm) can be used in all four mounting holes
B The ground pad of the mounting hole near J1, allows system grounding through a metal stand-off to
C The heat sink is grounded, and allows system grounding by mechanical connection to the system
D The supply must be mechanically supported using the PCB mounting holes and may be additionally
E
F
Molex 09-50-3131 or Molex 09-91-1300 mating connector with 2478
or equivalent crimp terminals.
(1.27)
without effecting safety approval.
the system chassis.
chassis.
supported by the heatsink mounting holes.
It is always advisable to attach the power supply heat sink to another thermal dissipator (such as a
chassis or finned heatsink etc). The resulting decrease in heat sink mounted component temperatures
will improve power supply lifetime.
A standard L-bracket and cover is available for mounting which contains all screws, connectors and
necessary mounting hardware. The kit is available, order part number “NFS110CJ” .
(6.35)
0.250
0.010
1.80 (45.72) MAX
(107.95)
4.250
0.020
(95.25)
3.750
0.005
0.250
0.010
(6.35)
C6
3.35 0.015 (85.09)
T1
T1
ALL DIMENSIONS IN INCHES (mm)
6.50 0.005 (165.1)
7.00 0.020 (177.8)
Pin 1
Optional
Power Fail
Detect Circuit
(Key = Pin 2)
Voltage Adjust
1.55 0.005
(39.37)
L1
5A, 250 VAC
F1
5V OUTPUT
PFD SIGNAL
AC INPUT
J1
J2
OPTIONAL POWER FAIL DETECT TIMING DIAGRAM
6-32 UNC
(4PL)
0-0.4 MAX
4.75V
LOW
(12.07)
0.475
0.010
PIN 1
0.156
DIA. HOLE
(4PL)
T1
PIN 1
1.00 0.005
(25.4)
HIGH
N/C = no connection
T2
Pin 10
Pin 11
Pin 12
Pin 13
Pin 1
Pin 2
Pin 3
Pin 1
Pin 2
Pin 3
Pin 4
Pin 5
Pin 6
Pin 7
Pin 8
Pin 9
J1
J2
3.5V MIN
110W
4.75V
T3
80W
11W
0W
0C
DERATING CURVE
Output Power (Watts)
AC Ground
AC Neutral
-7601PJ
AC Line
Return
Return
Return
Return
+5.1 V
+5.1 V
+5.1 V
+12 V
+12 V
-12 V
10C
-5 V
20 CFM FORCED AIR COOLING
PFD
11W MINIMUM LOAD REQUIRED AT 230VAC
Power fail detect signal (Note 8)
50ms ≤ T1 ≤ 200ms
T2 will vary with line and load
T3 ≥ 3ms
Pout: 110W
PFD output is an open collector which
will sink ≤ 40mA in the low state.
Embedded Power for
Business-Critical Continuity
20C
Pin Connections
CONVECTION
AC Ground
NATURAL
COOLING
AC Neutral
-7602 P
(See Notes 9, 10)
AC Line
Return
Return
Return
Return
+5.1 V
+5.1 V
+5.1 V
+12 V
+12 V
+24 V
30C
-12 V
Removed for Key
PFD
40C
AC Ground
AC Neutral
-7604PJ
AC Line
Return
Return
Return
Return
+5.1 V
+5.1 V
+5.1 V
+15 V
+15 V
50C
-15 V
PFD
-5 V
60C
Rev. 11.2.09_69
NFS110 Series
AC Ground
AC Neutral
Singles
AC Line
Return
Return
Return
Return
V out
V out
V out
V out
V out
70C
N/C
N/C
N/C
55W
40W
4 of 5