SI3011-F-FSR Silicon Laboratories Inc, SI3011-F-FSR Datasheet - Page 8

• Manufacturer Part Number: SI3011-F-FSR
• Manufacturer: Silicon Laboratories Inc

Specifications of SI3011-F-FSR

• Lead Free Status / RoHS Status: Supplier Unconfirmed

Table 4. AC Characteristics
(V
Si3050 + Si3011
8
Sample Rate
PCLK Input Frequency
Receive Frequency Response
Receive Frequency Response
Transmit Full-Scale Level
Receive Full-Scale Level
Dynamic Range
Receive Total Harmonic
Distortion
Receive Total Harmonic
Distortion
Dynamic Range (Caller ID mode)
Caller ID Full-Scale Level
Gain Accuracy
Transhybrid Balance
Transhybrid Balance
Two-Wire Return Loss
Two-Wire Return Loss
Notes:
Parameter
D
=
1. Measured at TIP and RING with 600 termination at 1 kHz, as shown in Figure 1 on page 6.
2. With FULL2 = 1, the transmit and receive full-scale level of +6.0 dBm can be achieved with a 600  termination. In this
3. Receive full-scale level produces –0.9 dBFS at DTX.
4. DR = 20 x log (RMS V
5. Measurement is 300 to 3400 Hz. Applies to both transmit and receive paths.
6. Vin = 1 kHz, –3 dBFS.
7. THD = 20 x log (RMS distortion/RMS signal).
8. DR
9. Refer to Tables 10–11 for relative gain accuracy characteristics (passband ripple).
10. Analog hybrid only. Z
3.0 to 3.6 V, T
mode, the DAA will transmit and receive +1.5 dBV into all reference impedances.
Here, V
enhanced caller ID circuit. With the typical CID circuit, the V
50 dB.
CID
6,7
6,7
= 20 x log (RMS V
FS
6,9
is the 0 dBm full-scale level per Note 1 above.
4,5,6
A
=
10
10
0 to 70 °C for F/K-Grade,
1,3
1
8
ACIM
FS
/RMS Vin) + 20 x log (RMS V
CID
controlled by ACIM in Register 30.
/RMS V
8
Symbol
DR
PCLK
THD
THD
V
IN
V
V
DR
Fs
CID
FS
FS
) + 20 x log (RMS V
CID
Fs = 8000 Hz,
Low –3 dBFS Corner, FILT = 0
Low –3 dBFS Corner, FILT = 1
DCR = 0, I
300–3.4 kHz,
1 kHz, all ac terminations
DCR = 0, I
FULL2 = 1 (+6.0 dBm)
FULL2 = 1 (+6.0 dBm)
VIN = 1 kHz, –13 dBFS
DCR = 0, I
TXG2, RXG2, TXG3,
Rev. 1.11
ILIM = 1, FULL2 = 0
ILIM = 1, FULL2 = 0
ILIM = 1, FULL2 = 0
1 kHz,
300–3.4 kHz, all ac
and RXG3 = 0000
in
Test Condition
/RMS noise). The RMS noise measurement excludes harmonics.
2-W to DTX,
terminations
IN
L
see
CID
Z
/RMS noise). V
= 20, 50, 100 mA
L
ACIM
L
"2. Typical Application Schematic" on page 17
= 20, 50 mA
full-scale level is 6 V peak, and the DR
Z
= 100 mA
ACIM
=
Z
LINE
=
Z
LINE
2
2
CID
is the 1.5 V full-scale level with the
–0.5
Min
256
—
—
—
—
—
—
—
—
—
20
—
25
—
8
2.16
2.16
Typ
200
–78
–72
1.5
—
—
80
62
30
32
—
—
5
0
8192
Max
CID
0.5
16
—
—
—
—
—
—
—
—
—
—
—
—
—
decreases to
V
V
V
Unit
kHz
kHz
PEAK
PEAK
PEAK
Hz
Hz
dB
dB
dB
dB
dB
dB
dB
dB
dB
)