5962-8871309RA E2V, 5962-8871309RA Datasheet - Page 6

• Manufacturer Part Number: 5962-8871309RA
• Manufacturer: E2V

Specifications of 5962-8871309RA

• Lead Free Status / RoHS Status: Supplier Unconfirmed

DSCC FORM 2234
APR 97
listed in 1.2 herein. In addition, the manufacturer's PIN may also be marked. For packages where marking of the entire SMD
PIN number is not feasible due to space limitations, the manufacturer has the option of not marking the "5962-" on the device.
compliance to MIL-PRF-38535, appendix A. The compliance indicator “C” shall be replaced with a "Q" or "QML" certification
mark in accordance with MIL-PRF-38535 to identify when the QML flow option is used.
approved source of supply in MIL-HDBK-103 (see 6.6 herein). The certificate of compliance submitted to DSCC-VA prior to
listing as an approved source of supply shall affirm that the manufacturer's product meets the requirements of MIL-PRF-
38535, appendix A and the requirements herein.
with each lot of microcircuits delivered to this drawing.
facility and applicable required documentation. Offshore documentation shall be made available onshore at the option of the
reviewer.
in a wide variety of configurations; two processing options are provided for selection in the contract, using an altered item
drawing.
3.2.2.1 and table II. It is recommended that users perform subgroups 7 and 9 after programming to verify the specific program
configuration.
herein, including the requirements of the altered item drawing, shall be satisfied by the manufacturer prior to delivery.
appendix A.
devices prior to quality conformance inspection. The following additional criteria shall apply:
3.5 Marking. Marking shall be in accordance with MIL-PRF-38535, appendix A. The part shall be marked with the PIN
3.5.1 Certification/compliance mark. A compliance indicator “C” shall be marked on all non-JAN devices built in
3.6 Certificate of compliance. A certificate of compliance shall be required from a manufacturer in order to be listed as an
3.7 Certificate of conformance. A certificate of conformance as required in MIL-PRF-38535, appendix A shall be provided
3.8 Notification of change. Notification of change to DSCC-VA shall be required for any change that affects this drawing.
3.9 Verification and review. DSCC, DSCC's agent, and the acquiring activity retain the option to review the manufacturer's
4. VERIFICATION
4.1 Sampling and inspection. Sampling and inspection procedures shall be in accordance with MIL-PRF-38535,
4.2 Screening. Screening shall be in accordance with method 5004 of MIL-STD-883, and shall be conducted on all
3.10 Processing options. Since the device is capable of being programmed by either the manufacturer or the user to result
3.10.1 Unprogrammed device delivered to the user. All testing shall be verified through group A testing as defined in
3.10.2 Manufacturer-programmed device delivered to the user. All testing requirements and quality assurance provisions
a. Burn-in test, method 1015 of MIL-STD-883.
b. Interim and final electrical test parameters shall be as specified in table II herein, except interim electrical parameter
(1)
(2) T
tests prior to burn-in are optional at the discretion of the manufacturer.
DEFENSE SUPPLY CENTER COLUMBUS
Test condition C or D. The test circuit shall be maintained by the manufacturer under document revision level
control and shall be made available to the preparing activity upon request. The test circuit shall specify the inputs,
outputs, biases, and power dissipation, as applicable, in accordance with the intent specified in method 1015 of
MIL-STD-883.
A
MICROCIRCUIT DRAWING
= +125°C, minimum.
COLUMBUS, OHIO 43218-3990
STANDARD
SIZE
A
REVISION LEVEL
A
SHEET
5962-88713
6