RFM02-DEMO

Manufacturer Part NumberRFM02-DEMO
DescriptionBOARD, DEMO, RFM02 TRANSMITTER
ManufacturerQUASAR
RFM02-DEMO datasheet
 


Specifications of RFM02-DEMO

Kit ContentsRFM02 Module, RF02 TX DEMO Module And RF01 RX DEMO ModuleFeaturesFSK Reception, Available In 433, 868 And 915MHz, Range Up To 300 Metres, Data Rate Up To 115.2kbps
Lead Free Status / RoHS StatusLead free / RoHS Compliant  
1
Page 1
2
Page 2
3
Page 3
4
Page 4
5
Page 5
6
Page 6
7
Page 7
Page 1/7

Download datasheet (240Kb)Embed
Next
RF02、 RF01 DEMO GUIDE
RF02,RF01 Demo Kit User Manual
Tel: +86-755-82973806 Fax: +86-755-82973550 E-mail: sales@hoperf.com
http://www.hoperf.com
1

RFM02-DEMO Summary of contents

  • Page 1

    RF02,RF01 Demo Kit User Manual Tel: +86-755-82973806 Fax: +86-755-82973550 E-mail: sales@hoperf.com http://www.hoperf.com RF02、 RF01 DEMO GUIDE 1 ...

  • Page 2

    ... General RF02,RF01 Demo Kit is used mainly to demonstrate the function of RFM02 and RFM01M FSK module, such as RF distance, and also useful for faster code development purpose. It consists of RF02 TX DEMO and RF01 RX DEMO. Products Introduction: 1. RF02 TX DEMO RFM02 TX Module Frequency Select Data Rate Select 2. ...

  • Page 3

    ... Attention: RF02 TX DEMO and RF01 RX DEMO setting has to be matching with each other for frequency and data rate so that RF link can be established. 1、Band and frequency:with BAND select, ON=1,OFF=0 SW1 Note: For RFM02B,the 315MHz band is not available 2、Data Rate:With Data RATE select, ON=1,OFF=0 SW1 ...

  • Page 4

    TX DEMO,RESERVED switch is used to select TX power: SW1 2.RF01 RX DEMO,RESERVED switch is used to select bandwidth: SW1 ...

  • Page 5

    Data Protocol: Preamble Sync word 0xAA,0xAA,0xAA 0x2D,0XD4 2.RF01 RX DEMO Step 1.Select reception frequency, data rate, sensitivity and demo mode(synchronized or FIFO reception mode)。Make sure reception frequency and data rate matches with the setting from RF02 TX DEMO. Step 2. ...

  • Page 6

    ... Testing needle RF02 TX DEMO and RF01 RX DEMO has all the RF module(RFM02、RFM01)pin connected externally for easier timing observation during their firmware development. If the MCU is removed, the RF module can be hooked to the target board to evaluate the RF module on end user’s system. Precautions: 1.Power supply range from 2.2V—5.5V Dip switch setting for TX and RX setting must be matching with each 2. ...

  • Page 7

    HOPE MICROELECTRONICS CO.,LTD Address: Rm B.8/F LiJingGe Emperor Regency 6012 ShenNan Rd, Shenzhen, China Tel: 86-755-82973805 Fax: 86-755-82973550 Email: sales@hoperf.com trade@hoperf.com Website: http://www.hoperf.com http://www.hoperf.cn http://hoperf.en.alibaba.com Tel: +86-755-82973806 Fax: +86-755-82973550 E-mail: sales@hoperf.com http://www.hoperf.com RF02、 RF01 DEMO GUIDE This document may contain ...