LTC2240IUP-10#TRPBF Linear Technology, LTC2240IUP-10#TRPBF Datasheet - Page 18

• Manufacturer Part Number: LTC2240IUP-10#TRPBF
• Description: IC ADC 10BIT 170MSPS 64-QFN
• Manufacturer: Linear Technology

Specifications of LTC2240IUP-10#TRPBF

• Number Of Bits: 10
• Sampling Rate (per Second): 170M
• Data Interface: Parallel
• Number Of Converters: 1
• Power Dissipation (max): 638mW
• Voltage Supply Source: Single Supply
• Operating Temperature: -40°C ~ 85°C
• Mounting Type: Surface Mount
• Package / Case: 64-WFQFN, Exposed Pad
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

APPLICATIONS INFORMATION
LTC2240-10
Other voltage ranges in between the pin selectable ranges
can be programmed with two external resistors as shown
in Figure 10. An external reference can be used by ap-
plying its output directly or through a resistor divider to
SENSE. It is not recommended to drive the SENSE pin
with a logic device. The SENSE pin should be tied to the
appropriate level as close to the converter as possible. If
the SENSE pin is driven externally, it should be bypassed
to ground as close to the device as possible with a 1μF
ceramic capacitor.
18
TIE TO V
TIE TO V
RANGE = 2 • V
CM
0.5V < V
DD
FOR 2V RANGE;
FOR 1V RANGE;
SENSE
SENSE
Figure 9. Equivalent Reference Circuit
1.25V
1μF
1μF
< 1V
FOR
Figure 10. 1.5V Range ADC
2.2μF
0.75V
8k
12k
1.25V
0.1μF
2.2μF
0.1μF
SENSE
REFHA
REFHB
REFLB
REFLA
V
CM
SENSE
2.2μF
1μF
LTC2240-10
V
CONTROL
CM
DETECT
2Ω
RANGE
AND
LTC2240-10
1.25V BANDGAP
DIFF AMP
REFERENCE
224010 F10
INTERNAL ADC
HIGH REFERENCE
INTERNAL ADC
LOW REFERENCE
1V
BUFFER
0.5V
224010 F09
Input Range
The input range can be set based on the application.
The 2V input range will provide the best signal-to-noise
performance while maintaining excellent SFDR. The 1V
input range will have better SFDR performance, but the
SNR will degrade by 1.7dB. See the Typical Performance
Characteristics section.
Driving the Encode Inputs
The noise performance of the LTC2240-10 can depend
on the encode signal quality as much as on the analog
input. The ENC
differentially, primarily for noise immunity from com-
mon mode noise sources. Each input is biased through
a 4.8k resistor to a 1.5V bias. The bias resistors set the
DC operating point for transformer coupled drive circuits
and can set the logic threshold for single-ended drive
circuits.
Any noise present on the encode signal will result in ad-
ditional aperture jitter that will be RMS summed with the
inherent ADC aperture jitter.
In applications where jitter is critical (high input frequen-
cies) take the following into consideration:
1. Differential drive should be used.
2. Use as large an amplitude as possible; if transformer
coupled use a higher turns ratio to increase the ampli-
tude.
3. If the ADC is clocked with a sinusoidal signal, fi lter the
encode signal to reduce wideband noise.
4. Balance the capacitance and series resistance at both
encode inputs so that any coupled noise will appear at both
inputs as common mode noise. The encode inputs have a
common mode range of 1.2V to 2.0V. Each input may be
driven from ground to V
+
/ENC
–
inputs are intended to be driven
DD
for single-ended drive.
224010fb