6450128-2 TE Connectivity, 6450128-2 Datasheet

MBXL R/A HDR STR 2P+24S+2P

6450128-2

Manufacturer Part Number
6450128-2
Description
MBXL R/A HDR STR 2P+24S+2P
Manufacturer
TE Connectivity
Datasheets
1.6450129-5.pdf (7 pages)
2.6450128-1.pdf (4 pages)

Specifications of 6450128-2

Product Series
XL
Connector Type
Header
Mount Angle
Right Angle
Termination Style
Solder
Mating Type
Squeeze-to-Release
Pcb Mount Retention
With
Guides
With
Voltage Rating (signal) (vac)
60
Voltage Rating (power) (vdc)
200
Termination Post Length (mm [in])
3.43 [0.135]
Sequencing
No
Pcb Mount Retention Type
Retention Clip/Post
Connector Configuration Orientation
Left-to-Right
Centerline, Dc Module (mm [in])
6.35 [0.250]
Centerline, Matrix (mm [in])
2.54 x 2.54 [.100 x .100]
Contact Type
Pin
Contact Material (power)
High Conductivity Copper
Contact Material (signal)
Copper Alloy
Contact Plating, Mating Area, Material
Gold (30)
Connector Style
Plug
Housing Material
High Temperature Thermoplastic
Total Number Of Dc Power
4
Total Number Of Signal
24
Connector Contact Configuration (no. Of Pos./type)
2/DC Power, 24/Signal, 2/DC Power
Rohs/elv Compliance
RoHS compliant, ELV compliant
Lead Free Solder Processes
Wave solder capable to 240°C, Wave solder capable to 260°C, Wave solder capable to 265°C
Rohs/elv Compliance History
Always was RoHS compliant
Application Use
Cable-to-Board
1.
1.1.
1.2.
1.3.
2.
2.1.
2.2.
3.
3.1.
©2011 Tyco Electronics Corporation,
a TE Connectivity Ltd. Company
All Rights Reserved
TE logo is a trademark.
SCOPE
Content
This specification covers performance, tests and quality requirements for the TE Connectivity (TE)
Multi-Beam XL* Board Mount Receptacle or Plug Connectors.
Qualification
When tests are performed on the subject product line, procedures specified in Figure 3 shall be used.
All inspections shall be performed using the applicable inspection plan and product drawing.
Qualification Test Results
Successful qualification testing on the subject product line was completed on 21Dec06. The
Qualification Test Report number for this testing is 501-646. This documentation is on file at and
available from Engineering Practices and Standards (EPS).
APPLICABLE DOCUMENTS
The following documents form a part of this specification to the extent specified herein. Unless
otherwise specified, the latest edition of the document applies. In the event of conflict between the
requirements of this specification and the product drawing, the product drawing shall take precedence.
In the event of conflict between the requirements of this specification and the referenced documents,
this specification shall take precedence.
TE Documents
!
!
!
!
!
!
Industry Standard
EIA-364: Electrical Connector/Socket Test Procedures Including Environmental Classifications
REQUIREMENTS
Design and Construction
Product shall be of the design, construction and physical dimensions specified on the applicable product
drawing.
108-2157-1: Product Specification (Multi-Beam XL Cable Plug)
109 Series: Test Specifications as indicated in Figure 3
109-197: Test Specification (TE Test Specifications vs EIA and IEC Test Methods)
114-13038: Application Specification (Multi-Beam XL Connectors)
501-597-1: Qualification Test Report (Multi-Beam XL Cable Plug)
501-646: Qualification Test Report (Multi-Beam XL Board Mount Receptacle or Plug Connector
System)
| Indicates change
*Trademark
Product
Specification
Multi-Beam XL* Board Mount Receptacle or Plug Connector
System
For latest revision, visit our website at www.te.com/documents.
For Regional Customer Service, visit our website at www.te.com
Other products, logos, and company names might be trademarks of their respective owners.
108-1973
11Mar11 Rev C
1 of 7
LOC B

Related parts for 6450128-2

Image
Part Number
Description
Manufacturer
Datasheet
Request R
645-102/8
Part Number:
645-102/8
Description:
SB 02P 3.50mm Gray 45d
Manufacturer:
BLOCKMASTER ELECTRONICS
645-102/85
Part Number:
645-102/85
Description:
SB 02P 3.50mm Gray/Green
Manufacturer:
BLOCKMASTER ELECTRONICS
645-103/8
Part Number:
645-103/8
Description:
SB 03P 3.50mm Gray 45d
Manufacturer:
BLOCKMASTER ELECTRONICS
645-104/5869
Part Number:
645-104/5869
Description:
SB 04P 3.50mm Grn/Gry/Blue/Wht
Manufacturer:
BLOCKMASTER ELECTRONICS
645-104/8596
Part Number:
645-104/8596
Description:
SB 04P 3.50mm Gry/Grn/Wht/Blue
Manufacturer:
BLOCKMASTER ELECTRONICS
120732-1
Part Number:
120732-1
Description:
High Speed / Modular Connectors 30P HEADER ASSY
Manufacturer:
TE Connectivity
Datasheet:
120670-1.pdf (7 pages)
120788-1
Part Number:
120788-1
Description:
High Speed / Modular Connectors REC 6X005P R/A LT B-PLANE HS3
Manufacturer:
TE Connectivity
Datasheet:
120670-1.pdf (7 pages)
120792-1
Part Number:
120792-1
Description:
High Speed / Modular Connectors 2MM HM RCPT 50P R/A AU
Manufacturer:
TE Connectivity
Datasheet:
120792-1.pdf (1 page)
120793-1
Part Number:
120793-1
Description:
High Speed / Modular Connectors 2MM HM RCPT 50P R/A AU
Manufacturer:
TE Connectivity
Datasheet:
120793-1.pdf (1 page)
280388-2
Part Number:
280388-2
Description:
Manufacturer:
TE Connectivity
Datasheet:
280388-2.pdf (1 page)
1-826632-7
Part Number:
1-826632-7
Description:
Manufacturer:
TE Connectivity
Datasheet:
1-826632-1.pdf (1 page)
280375-1
Part Number:
280375-1
Description:
Manufacturer:
TE Connectivity
Datasheet:
280370-3.pdf (1 page)
3-826947-6
Part Number:
3-826947-6
Description:
Manufacturer:
TE Connectivity
Datasheet:
1-826947-1.pdf (1 page)
5-826953-0
Part Number:
5-826953-0
Description:
Manufacturer:
TE Connectivity
Datasheet:
1-826953-9.pdf (1 page)
8-1734774-1
Part Number:
8-1734774-1
Description:
Manufacturer:
TE Connectivity
Datasheet:
1-1734774-0.pdf (4 pages)

6450128-2 Summary of contents

Page 1

... System 1. SCOPE 1.1. Content This specification covers performance, tests and quality requirements for the TE Connectivity (TE) Multi-Beam XL* Board Mount Receptacle or Plug Connectors. 1.2. Qualification When tests are performed on the subject product line, procedures specified in Figure 3 shall be used. All inspections shall be performed using the applicable inspection plan and product drawing. ...

Page 2

Materials Materials used in the construction of this product shall be as specified on the applicable product drawing. 3.3. Ratings ! Voltage: See Figure 1 ! Current: See Figure 2 ! Temperature: -20 to 105° C Contact Contact Pitch ...

Page 3

Test Requirements and Procedures Summary Test Description Initial examination of product. Final examination of product. Low level contact resistance, signal and power contacts. Contact resistance at rated current, power contacts. Insulation resistance. Withstanding voltage. Temperature rise vs current. Vibration, ...

Page 4

Test Description Mechanical shock. Durability. Mating force. Unmating force. Compliant pin insertion. Radial hole distortion. Compliant pin retention. Component heat resistance to wave soldering. Solderability dip test. Thermal shock. Rev C Requirement No discontinuities of 1 microsecond or longer duration. ...

Page 5

Test Description Humidity-temperature cycling. Temperature life. Mixed flowing gas. Shall meet visual requirements, show no physical damage, and meet requirements of additional NOTE tests as specified in the Product Qualification and Requalification Test Sequence shown in Figure 4. Rev C ...

Page 6

Product Qualification and Requalification Test Sequence Test or Examination Initial examination of product Low level contact resistance, signal and power contacts Low level contact resistance, power contacts only Contact resistance at rated current, power contacts Insulation resistance Withstanding voltage ...

Page 7

QUALITY ASSURANCE PROVISIONS 4.1. Qualification Testing A. Specimen Selection Specimens shall be prepared in accordance with applicable Instruction Sheets and shall be selected at random from current production. Test Groups 1 and 4 were carried over from the qualification ...

Related keywords