AD1674KNZ Analog Devices Inc, AD1674KNZ Datasheet - Page 4

• Manufacturer Part Number: AD1674KNZ
• Description: IC ADC 12BIT 100KSPS 28-DIP
• Manufacturer: Analog Devices Inc

Specifications of AD1674KNZ

• Data Interface: Parallel
• Number Of Bits: 12
• Sampling Rate (per Second): 100k
• Number Of Converters: 1
• Power Dissipation (max): 825mW
• Voltage Supply Source: Dual ±
• Operating Temperature: 0°C ~ 70°C
• Mounting Type: Through Hole
• Package / Case: 28-DIP (0.600", 15.24mm)
• Resolution (bits): 12bit
• Sampling Rate: 100kSPS
• Input Channel Type: Single Ended
• Supply Voltage Range - Digital: 4.5V To 5.5V
• Supply Current: 14mA
• Digital Ic Case Style: DIP
• Number Of Elements: 1
• Resolution: 12Bit
• Architecture: SAR
• Sample Rate: 100KSPS
• Input Polarity: Unipolar/Bipolar
• Input Type: Voltage
• Rated Input Volt: 10/20/±5/±10V
• Differential Input: No
• Power Supply Requirement: Dual
• Single Supply Voltage (typ): Not RequiredV
• Single Supply Voltage (min): Not RequiredV
• Single Supply Voltage (max): Not RequiredV
• Dual Supply Voltage (typ): ±12/±15V
• Dual Supply Voltage (min): ±11.4V
• Dual Supply Voltage (max): ±16.5V
• Power Dissipation: 575mW
• Integral Nonlinearity Error: ±0.5LSB
• Operating Temp Range: 0C to 70C
• Operating Temperature Classification: Commercial
• Mounting: Through Hole
• Pin Count: 28
• Package Type: PDIP W
• Input Signal Type: Single-Ended
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant, Lead free / RoHS Compliant

AD1674–SPECIFICATIONS
AC SPECIFICATIONS
Parameter
Signal to Noise and Distortion (S/N+D) Ratio
Total Harmonic Distortion (THD)
Peak Spurious or Peak Harmonic Component
Full Power Bandwidth
Full Linear Bandwidth
Intermodulation Distortion (IMD)
SHA (Specifications are Included in Overall Timing Specifications)
DIGITAL SPECIFICATIONS
Parameter
LOGIC INPUTS
LOGIC OUTPUTS
NOTES
1
2
3
4
5
All min and max specifications are guaranteed.
Specifications subject to change without notice.
f
otherwise noted.
Specified at worst case temperatures and supplies after one minute warm-up.
See Figures 12 and 13 for other input frequencies and amplitudes.
See Figure 11.
fa = 9.08 kHz, fb = 9.58 kHz with f
IN
Second Order Products
Third Order Products
Aperture Delay
Aperture Jitter
Acquisition Time
V
V
I
I
C
V
V
I
C
IH
IL
OZ
amplitude = –0.5 dB (9.44 V p-p) 10 V bipolar mode unless otherwise noted. All measurements referred to –0 dB (9.997 V p-p) input signal unless
IH
IL
OH
OL
IN
OZ
High Level Input Voltage
Low Level Input Voltage
High Level Input Current (V
Low Level Input Current (V
Input Capacitance
High Level Output Voltage
Low Level Output Voltage
High-Z Leakage Current
High-Z Output Capacitance
SAMPLE
(T
–12 V
MIN
5
= 100 kHz. See Definition of Specifications section and Figure 15.
4
to T
(for all grades T
V
MAX
5%, f
EE
, with V
= –15 V
IN
IN
SAMPLE
= 0 V)
2, 3
= 5 V)
CC
= 100 kSPS, f
= +15 V
10% or –12 V
MIN
to T
MAX
Test Conditions
V
V
I
I
V
OH
OL
10% or +12 V
IN
IN
IN
, with V
IN
–4–
= 1.6 mA
= 0.5 mA
= 10 kHz, stand-alone mode unless otherwise noted)
= V
= 0 V
= 0 to V
Min
69
5%)
LOGIC
CC
= +15 V
AD1674J/A
LOGIC
Typ
70
–90
–92
1
500
–90
–90
50
250
1
5%, V
10% or +12 V
LOGIC
Max
0.008
–82
–80
–80
Min
+2.0
–0.5
–10
–10
+2.4
–10
–82
= +5 V
Min
70
1
500
10%, V
5%, V
AD1674K/B/T
Max
V
+0.8
+10
+10
10
+0.4
+10
10
LOGIC
LOGIC
EE
Typ
71
–90
–92
50
250
1
–90
–90
= –15 V
= +5 V
+0.5 V
1
Max
–82
0.008
–82
–80
–80
10% or
10%,
Units
V
V
pF
V
V
pF
A
A
A
REV. C
Units
dB
dB
%
dB
MHz
kHz
dB
dB
ns
ps
s