AD7677AST Analog Devices Inc, AD7677AST Datasheet - Page 11

• Manufacturer Part Number: AD7677AST
• Description: IC ADC 16BIT 1MSPS DIFF 48-LQFP
• Manufacturer: Analog Devices Inc
• Series: PulSAR®r

Specifications of AD7677AST

• Rohs Status: RoHS non-compliant
• Number Of Bits: 16
• Sampling Rate (per Second): 1M
• Data Interface: Serial, Parallel
• Number Of Converters: 1
• Power Dissipation (max): 130mW
• Voltage Supply Source: Analog and Digital
• Operating Temperature: -40°C ~ 85°C
• Mounting Type: Surface Mount
• Package / Case: 48-LQFP
• For Use With: EVAL-AD7677CBZ - BOARD EVALUATION FOR AD7677

CIRCUIT INFORMATION
The AD7677 is a very fast, low power, single-supply, precise,
16-bit analog-to-digital converter (ADC). The AD7677 features
different modes to optimize performances according to the
applications.
In Warp Mode, the AD7677 is capable of converting 1,000,000
samples per second (1 MSPS).
The AD7677 provides the user with an on-chip track/hold,
successive approximation ADC that does not exhibit any pipe-
line or latency, making it ideal for multiple multiplexed channel
applications.
The AD7677 can be operated from a single 5 V supply and
be interfaced to either 5 V or 3 V digital logic. It is housed in a
48-lead LQFP package that combines space savings and flexible
configurations as either serial or parallel interface. The AD7677
is a pin-to-pin compatible upgrade of the AD7664, AD7675,
and AD7676.
CONVERTER OPERATION
The AD7677 is a successive approximation analog-to-digital
converter based on a charge redistribution DAC. Figure 3 shows
the simplified schematic of the ADC. The capacitive DAC con-
sists of two identical arrays of 16 binary weighted capacitors
that are connected to the two comparator inputs.
REV. A
TPC 13. Power-Down Operating Currents vs. Temperature
250
200
150
100
50
0
–55
REFGND
–35
REF
IN+
IN–
–15
TEMPERATURE – C
5
25
45
32,768C 16,384C
32,768C 16,384C
65
Figure 3. ADC Simplified Schematic
OVDD
85
AVDD
MSB
MSB
DVDD
105
4C
4C
–11–
2C
2C
During the acquisition phase, terminals of the array tied to the
comparator’s input are connected to AGND via SW
All independent switches are connected to the analog inputs.
Thus, the capacitor arrays are used as sampling capacitors and
acquire the analog signal on IN+ and IN– inputs. When the
acquisition phase is complete and the CNVST input goes
low, a conversion phase is initiated. When the conversion phase
begins, SW
are then disconnected from the inputs and connected to the
REFGND input. Therefore, the differential voltage between the
inputs IN+ and IN– captured at the end of the acquisition phase
is applied to the comparator inputs, causing the comparator to
become unbalanced. By switching each element of the capacitor
array between REFGND or REF, the comparator input varies
by binary weighted voltage steps (V
The control logic toggles these switches, starting with the MSB
first, in order to bring the comparator back into a balanced
condition. After the completion of this process, the control logic
generates the ADC output code and brings BUSY output low.
Modes of Operation
The AD7677 features three modes of operations, Warp, Normal,
and Impulse. Each of these modes is more suitable for specific
applications.
C
C
–1
–2
–3
–4
–5
5
4
3
2
1
0
–55
+
and SW
C
C
–35
LSB
TPC 14. Drift vs. Temperature
LSB
–15
–
SW +
are opened first. The two capacitor arrays
SW –
COMP
–5
+FS
–FS
OFFSET
TEMPERATURE – C
15
SWITCHES
CONTROL
35
CONTROL
REF
LOGIC
CNVST
/2, V
55
REF
75
OUTPUT
BUSY
CODE
/4 . . . V
95
AD7677
115
+
REF
and SW
/65536).
135
–
.