MAX5483ETE+T Maxim Integrated Products, MAX5483ETE+T Datasheet - Page 16

• Manufacturer Part Number: MAX5483ETE+T
• Description: IC POT DGTL 10BIT NV 16-TQFN
• Manufacturer: Maxim Integrated Products

Specifications of MAX5483ETE+T

• Taps: 1024
• Resistance (ohms): 10K
• Number Of Circuits: 1
• Temperature Coefficient: 35 ppm/°C Typical
• Memory Type: Non-Volatile
• Interface: SPI, 3-Wire Serial
• Voltage - Supply: 2.7 V ~ 5.25 V, ±2.5 V ~ 5.25 V
• Operating Temperature: -40°C ~ 85°C
• Mounting Type: Surface Mount
• Package / Case: 16-TQFN Exposed Pad
• Resistance In Ohms: 10K
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

The copy wiper register to NV register command (C1,
C0 = 10) stores the current position of the wiper to the
NV register for use at power-up. Figure 6 shows how to
copy data from wiper register to NV register. The oper-
ation takes up to 12ms (max) after CS goes high to
complete and no other operation should be performed
until completion.
The copy NV register to wiper register (C1, C0 = 11)
restores the wiper position to the current value stored in
the NV register. Figure 7 shows how to copy data from
the NV register to the wiper register.
Figure 8 illustrates an up/down serial-interface timing
diagram. In digital up/down interface mode (SPI/UD =
0), the logic inputs CS, DIN(U/D), and SCLK(INC) con-
trol the wiper position and store it in nonvolatile memory
(see Table 3). The chip-select (CS) input enables the
serial interface when low and disables the interface
when high. The position of the wiper is stored in the
nonvolatile register when CS transitions from low to
high while SCLK(INC) is high.
When the serial interface is active (CS low), a high-to-
low (falling edge) transition on SCLK(INC) increments
or decrements the internal 10-bit counter depending on
the state of DIN(U/D). If DIN(U/D) is high, the wiper
increments. If DIN(U/D) is low, the wiper decrements.
The device stores the value of the wiper position in the
nonvolatile memory when CS transitions from low to high
while SCLK(INC) is high. The host system can disable
10-Bit, Nonvolatile, Linear-Taper Digital
Potentiometers
Table 3. Truth Table
↑ = Low-to-high transition.
↓ = High-to-low transition.
X = Don’t care.
16
CS
H
L
L
L
↓
↑
↑
______________________________________________________________________________________
DIN(U/D)
H
L
X
X
X
X
X
Copy Wiper Register to NV Register
Copy NV Register to Wiper Register
Digital Up/Down Interface
SCLK(INC)
H
↓
↓
↑
X
X
L
Position Not Stored
Position Stored
No Change
No Change
No Change
Decrement
Increment
W
the serial interface and deselect the device without stor-
ing the latest wiper position in the nonvolatile memory by
keeping SCLK(INC) low while taking CS high.
Upon power-up, the MAX5481–MAX5484 load the
value of nonvolatile memory into the wiper register, and
set the wiper position to the value last stored.
Figure 6. Copy Wiper Register to NV Register Operation
Figure 7. Copy NV Register to Wiper Register Operation
SCLK(INC)
DIN(U/D)
SCLK(INC)
ACTION
DIN(U/D)
ACTION
CS
CS
0
0
1
1
0
0
2
2
C1
C1
1
1
3
3
C0
C0
1
0
4
4
0
0
5
5
0
0
6
6
0
0
7
7
0
0
8
8
(DEVICE IS
REGISTER
UPDATED
WRITE NV
REGISTER
WIPER
BUSY)
t
BUSY