CAPACITOR, X1/Y1 4.7NF CAPACITOR, X1/Y1 4.7NF

DE1E3KX472MA5B

Manufacturer Part NumberDE1E3KX472MA5B
DescriptionCAPACITOR, X1/Y1 4.7NF CAPACITOR, X1/Y1 4.7NF
ManufacturerMurata
SeriesKX
DE1E3KX472MA5B datasheet
 


Specifications of DE1E3KX472MA5B

Capacitance4700PFCapacitor Dielectric TypeCERAMIC DISC AND PLATE
Tolerance,20%Tolerance, -20%
Temp, Op. Max125(DEGREE C)Temp, Op. Min-25(DEGREE C)
Pitch,ROHS COMPLIANT  
1
Page 1
2
Page 2
3
Page 3
4
Page 4
5
Page 5
6
Page 6
7
Page 7
8
Page 8
9
Page 9
10
Page 10
Page 7/10

Download datasheet (177Kb)Embed
PrevNext
Continued from the preceding page.
No.
Item
Appearance
No marked defect
Capacitance
Within ±10%
Change
I.R.
1000MΩ min.
Soldering
9
Effect
(Non-Preheat)
Dielectric
Per Item 6
Strength
Appearance
No marked defect
Capacitance
Within ±10%
Change
I.R.
1000MΩ min.
Soldering
10
Effect
(On-Preheat)
Dielectric
Per Item 6
Strength
Appearance
No marked defect
Capacitance
Within the specified tolerance
Vibration
Char.
11
Resistance
B, E
D.F.
F
Q
SL
Appearance
No marked defect
Char.
Capacitance
B
E, F
Change
SL
Humidity
(Under
Char.
12
Steady
B, E
D.F.
State)
F
Q
SL
3000MΩ min.
I.R.
Dielectric
Per Item 6
Strength
Appearance
No marked defect
Char.
Capacitance
B
Change
E, F
SL
Char.
Humidity
13
B, E
Loading
D.F.
F
Q
SL
I.R.
3000MΩ min.
Dielectric
Per Item 6
Strength
1
*
"C" expresses nominal capacitance value (pF).
2
*
"room condition" Temperature: 15 to 35°C, Relative humidity: 45 to 75%, Atmospheric pressure: 86 to 106kPa
Specifications and Test Methods
Specifications
As shown in figure, the lead wires
should be immersed in solder of
350±10°C or 260±5°C up to 1.5
to 2.0mm from the root of terminal
for 3.5±0.5 sec. (10±1 sec. for
260±5°C).
Pre-treatment:
Capacitor should be stored at 85±2°C for 1 hr., then placed at
room condition for 24±2 hrs. before initial measurements.
2
Post-treatment:
Capacitor should be stored for 1 to 2 hrs. at
First the capacitor should be
stored at 120+0/-5°C for
60+0/-5 sec.
Then, as in figure, the lead wires
should be immersed solder of
260+0/-5°C up to 1.5 to 2.0mm
from the root of terminal for
7.5+0/-1 sec.
Pre-treatment:
Capacitor should be stored at 85±2°C for 1 hr., then placed at
2
room condition for 24±2 hrs. before initial measurements.
Post-treatment:
Capacitor should be stored for 1 to 2 hrs. at
The capacitor should be firmly soldered to the supporting lead
wire and vibrated at a frequency range of 10 to 55Hz, 1.5mm in
total amplitude, with about a 1 minute rate of vibration change
Specifications
from 10Hz to 55Hz and back to 10Hz.
D.F.V2.5%
Apply for a total of 6 hrs., 2 hrs. each in 3 mutually
D.F.V5.0%
perpendicular directions.
*1
QU400+20C
(CF30pF)
QU1000
(CU30pF)
Capacitance Change
Within ±10%
Within ±15%
Within ± 5%
Set the capacitor for 500±12 hrs. at 40±2°C in 90 to 95%
relative humidity.
Specifications
Post-treatment:
D.F.V5.0%
Capacitor should be stored for 1 to 2 hrs. at
D.F.V7.5%
*1
QU275+5/2C
(CF30pF)
QU350
(CU30pF)
Capacitance Change
Within ±10%
Within ±15%
Within ± 5%
Apply the rated voltage for 500±12 hrs. at 40±2°C in 90 to 95%
Specifications
relative humidity.
D.F.V5.0%
Post-treatment:
D.F.V7.5%
Capacitor should be stored for 1 to 2 hrs. at
*1
QU275+5/2C
(CF30pF)
QU350
(CU30pF)
Testing Method
Capacitor
Thermal
Screen
1.5
to 2.0mm
Molten
Solder
room condition.
2
Capacitor
Thermal
Screen
1.5
to 2.0mm
Molten
Solder
2
room condition.
2
room condition.
room condition.
2
Continued on the following page.