MAX5632UCB+D Maxim Integrated Products, MAX5632UCB+D Datasheet
MAX5632UCB+D
Specifications of MAX5632UCB+D
Related parts for MAX5632UCB+D
MAX5632UCB+D Summary of contents
Page 1
... Pin Configurations continued at end of data sheet. SPI and QSPI are trademarks of Motorola, Inc. MICROWIRE is a trademark of National Semiconductor, Corp. ________________________________________________________________ Maxim Integrated Products For pricing, delivery, and ordering information, please contact Maxim/Dallas Direct! at 1-888-629-4642, or visit Maxim’s website at www.maxim-ic.com. 16-Bit DACs with 32-Channel ...
Page 2
DACs with 32-Channel Sample-and-Hold Outputs ABSOLUTE MAXIMUM RATINGS V to AGND.......................................................-0.3V to +12. AGND .........................................................-6.0V to +0. ...........................................................................+15V AGND or DGND ..............-0.3V to +6V ...
Page 3
ELECTRICAL CHARACTERISTICS (continued +10V -4V LOGIC CLKSEL = +5V 400kHz ECLK A PARAMETER SYMBOL DYNAMIC CHARACTERISTICS Sample-and-Hold Settling SCLK Feedthrough f Feedthrough SEQ Hold-Step Droop Rate ...
Page 4
DACs with 32-Channel Sample-and-Hold Outputs ELECTRICAL CHARACTERISTICS (continued +10V -4V LOGIC LDAC CLKSEL = +5V 400kHz ECLK A MIN PARAMETER SYMBOL SCLK High to CS ...
Page 5
V = -4V +2.5V REF INTEGRAL NONLINEARITY vs. CODE 0.007 0.005 0.003 0.001 -0.001 -0.003 -0.005 -0.007 4018 11769 19520 27271 35021 42723 58268 INPUT CODE DIFFERENTIAL NONLINEARITY VS. TEMPERATURE 1.0 0.9 ...
Page 6
DACs with 32-Channel Sample-and-Hold Outputs (V = +10V -4V +2.5V REF LOGIC SUPPLY CURRENT vs. LOGIC SUPPLY VOLTAGE 900 800 700 600 500 INTERFACE INACTIVE 400 4.75 5.00 5.25 5.50 LOGIC SUPLY ...
Page 7
PIN TQFP QFN 17, 34, 51 15, 25, 40, 55, 62 ...
Page 8
DACs with 32-Channel Sample-and-Hold Outputs PIN TQFP QFN ECLK ...
Page 9
CS t CSHO t t CSSO CH SCLK B23 DIN Figure 2. Serial Interface Timing Diagram Detailed Description Digital-to-Analog Converter The MAX5631/MAX5632/MAX5633 16-bit digital-to-ana- log converters (DAC) are composed of two matched sections. The four MSBs ...
Page 10
DACs with 32-Channel Sample-and-Hold Outputs voltage at the ground-sense input. With a 2.5V refer- ence, the nominal endpoints are -4.0535V and +9.0535V (Table 1). Note that these are “virtual” inter- nal endpoint voltages and cannot be reached with all ...
Page 11
Table 2. Channel/Output Selection ...
Page 12
DACs with 32-Channel Sample-and-Hold Outputs The operating modes can also be selected externally through CLKSEL and IMMED. In the case where the control bit in the serial word and the external signal conflict, the signal that is a logic ...
Page 13
Burst Mode allows multiple SRAM locations to be loaded at high speed. During Burst Mode, the output voltages are not updated until the data burst is com- plete and control returns ...
Page 14
DACs with 32-Channel Sample-and-Hold Outputs +2.5V Figure 7. Typical Operating Circuit Pin Configurations (continued) TOP VIEW 1 N.C. N. LDAC RST DIN 7 SCLK MAX5631 LOGIC MAX5632 IMMED ...
Page 15
For the latest package outline information go to www.maxim-ic.com/packages.) ______________________________________________________________________________________ 16-Bit DACs with 32-Channel Sample-and-Hold Outputs PACKAGE OUTLINE, 64L TQFP, 10x10x1.4mm PACKAGE OUTLINE, 64L TQFP, 10x10x1.4mm ...
Page 16
... Maxim cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim product. No circuit patent licenses are implied. Maxim reserves the right to change the circuitry and specifications without notice at any time. 16 ____________________Maxim Integrated Products, 120 San Gabriel Drive, Sunnyvale, CA 94086 408-737-7600 © 2005 Maxim Integrated Products ...