CS42432-CMZ Cirrus Logic Inc, CS42432-CMZ Datasheet - Page 34

• Manufacturer Part Number: CS42432-CMZ
• Description: IC CODEC 108DB 192KHZ 52-MQFP
• Manufacturer: Cirrus Logic Inc
• Type: Audio Codecr

Specifications of CS42432-CMZ

• Package / Case: 52-VQFN
• Data Interface: Serial
• Resolution (bits): 24 b
• Number Of Adcs / Dacs: 4 / 6
• Sigma Delta: Yes
• Dynamic Range, Adcs / Dacs (db) Typ: 105 / 108 (Differential), 102 / 105 (Single-Ended)
• Voltage - Supply, Analog: 3.14 V ~ 5.25 V
• Voltage - Supply, Digital: 3.14 V ~ 3.47 V
• Operating Temperature: -10°C ~ 70°C
• Mounting Type: Surface Mount
• Number Of Adc Inputs: 4
• Number Of Dac Outputs: 6
• Conversion Rate: 192 KSPS
• Interface Type: Serial (I2C, SPI)
• Resolution: 24 bit
• Maximum Operating Temperature: + 70 C
• Mounting Style: SMD/SMT
• Minimum Operating Temperature: - 10 C
• Number Of Channels: 4 ADC/6 DAC
• Thd Plus Noise: - 98 dB ADC / - 98 dB DAC
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant, Lead free / RoHS Compliant
• Other names: 598-1608

34
5.7.2
C C L K
CS
C D IN
C D O U T
SDA
SCL
I²C Mode
In I²C Mode, SDA is a bidirectional data line. Data is clocked into and out of the part by the clock, SCL.
There is no CS pin. Pins AD0 and AD1 form the two least-significant bits of the chip address and should
be connected through a resistor to VLC or DGND as desired. The state of the pins is sensed while the
CS42432 is being reset.
The signal timings for a read and write cycle are shown in
defined as a falling transition of SDA while the clock is high. A Stop condition is a rising transition while
the clock is high. All other transitions of SDA occur while the clock is low. The first byte sent to the
CS42432 after a Start condition consists of a 7-bit chip address field and a R/W bit (high for a read, low
for a write). The upper 5 bits of the 7-bit address field are fixed at 10010. To communicate with a CS42432,
the chip address field, which is the first byte sent to the CS42432, should match 10010 followed by the
settings of the AD1 and AD0. The eighth bit of the address is the R/W bit. If the operation is a write, the
next byte is the Memory Address Pointer (MAP) which selects the register to be read or written. If the op-
eration is a read, the contents of the register pointed to by the MAP will be output. Setting the auto-incre-
ment bit in MAP allows successive reads or writes of consecutive registers. Each byte is separated by an
acknowledge bit. The ACK bit is output from the CS42432 after each input byte is read, and is input to the
CS42432 from the microcontroller after each transmitted byte.
ADDRESS
MAP = Memory Address Pointer, 8 bits, MSB first
1001111
C H IP
START
0
1
CHIP ADDRESS (WRITE)
1
0
High Impedance
0
2
1
R/W
3
0 AD1 AD0 0
4
5
M A P
Figure 16. Control Port Timing in SPI Mode
6
Figure 17. Control Port Timing, I²C Write
7
ACK
8
MSB
b y te 1
INCR
9
10 11
6
DATA
MAP BYTE
5
12
4
b y te n
13 14 15
3
LSB
2
1
16 17 18
0
ACK
A D D R E S S
7
C H IP
1001111
19
6
DATA
Figure 17
24 25
1
0
ACK
R/W
26
27 28
7
MSB
and
DATA +1
6
Figure
1
0
LSB MSB
7
18. A Start condition is
DATA +n
6
1
0
ACK
CS42432
STOP
LSB
DS673F2