VQ1301N-51 SMC Corporation, VQ1301N-51 Datasheet - Page 67

• Manufacturer Part Number: VQ1301N-51
• Description: SOLENOID VALVE, BASE MT, 5 PORT, PLUG-IN TYPE, 24VDC, 3 POSITION CLOSED CENTER
• Manufacturer: SMC Corporation
• Type: Solenoidr

Specifications of VQ1301N-51

• Brand/series: VQ Series
• Configuration: 3-Position Closed Center
• Enclosure Rating: IP65
• Fluid Type: Air/Inert Gas
• Number Of Ports: 5
• Pressure, Operating: 0.7 MPa
• Primary Type: Solenoid Valve
• Temperature, Ambient: –10° to +50°C
• Valve Type: 5-Port Solenoid, Plug-In, Base Mounted with 3 Position Closed Center Actuation, Rubber Seal, Negative Common
• Voltage, Coil: 24 VDC

EXH block base assembly
VVQ1000-19A-
Manifold block assembly
Electrical entry
The manifold block assembly is used between stations for
which exhaust is desired to be divided when valve exhaust
affects other stations due to the circuit configuration. The
EXH passage on the D-side is blocked in the EXH block
base assembly. It is also used in combination with an individ-
ual EXH spacer for individual exhaust.
<Block indication label>
Indication labels to confirm the blocking position are at-
tached. (Each for EXH passage and SUP/EXH passage
blocking positions)
Back pressure check valve assembly [-B]
VVQ1000-18A
It prevents cylinder malfunction caused by other valve exhaust
entry. Insert it into R (EXH) port on the manifold side of a valve
which is affected. It is effective when a single-acting cylinder is
used or an exhaust center type solenoid valve is used.
Note) When a back pressure check valve is desired, and is to
Name plate [-N]
VVQ1000-
It is a transparent resin plate for placing a label that in-
dicates solenoid valve function, etc.
Insert it into the groove on the side of the end plate
and bend it as shown in the figure.
Blanking plug (For one-touch fittings)
KQ2P-„
It is inserted into an unused cylinder port
and SUP/EXH ports.
Purchasing order is available in units of 10
pieces.
Port plug
VVQ0000-58A
The plug is used to block the cylinder port.
Elbow fitting assembly
VVQ1000-F-L(C3/C4/C6/M5/N1/N3/N7)
It is used for piping that extends upward or downward from the
manifold.
When installing it in part of the manifold stations, specify the elbow
fitting assembly part number and the mounting station by means of
the manifold specification sheet.
F0
F1
F2
F3
P1
P2
P3
L0
L1
L2
When ordering a EXH block base incorporated with a mani-
fold, a block indication label is attached to the manifold.
When ordering it being mounted on all manifold stations, suf-
fix “-B” to the end of the manifold part number.
When the blanking plate with connector is mounted, it
automatically will be “VVQ1000-NC-n”
fold, suffix “-N” to the end of the manifold part number.
size of the manifold part number, as well as, the mounting station and cylinder port
mounting positions 4(A) and 2(B) by means of the manifold specification sheet.
Gently screw an M3 screw in the port plug hole and pull it for removal.
“L„” or “B„” for the manifold port size (when installed in all sta-
tions.)
station and a silencer on EXH port, select a silencer, AN203-KM8.
A silencer (AN200-KM8) is interfered with fittings.
When ordering this option incorporated with a mani-
When ordering this option incorporated with a manifold, indicate “CM” for the port
When ordering this option incorporated with a manifold, indicate
When mounting elbow fitting assembly on the edge of manifold
be installed only in certain manifold stations, clearly indi-
cate the part number and specify the mounting station
by means of the manifold specification sheet.
Without lead wire
For F kit (2 to 12 stations)/Double wiring
For F kit (13 to 24 stations)/Double wiring
For F kit (2 to 24 stations)/Single wiring
For P, G, T, S kit (2 to 12 stations)/Double wiring
For P, G, T, S kit (13 to 24 stations)/Double wiring
For P, G, T, S kit (2 to 24 stations)/Single wiring
L0 kit
L1 kit
L2 kit
N
NC
1 to 8 stations
-N-Station (1 to Max. stations)
F
P
L
-(C3/C4/C6/M5/N1/N3/N7)
N: Standard
NC: For mounting
specification sheet.
When ordering this option incorporated with a manifold,
specify the EXH block base assembly part number with
“ ” in front of it beneath the manifold part number.
Specify the mounting station by means of the manifold
blanking plate
with connector
EXH
passage blocked
Solid forming
Base Mounted
EXH passage blocked
2 pcs. in 1 set
Dimensions
Applicable
fitting size
Plug-in Unit
Black screw
ø
3.2
4
6
8
d
Block indication label
KQ2P-23
KQ2P-04
KQ2P-06
KQ2P-08
Model
Note) ( ): VVQ1000-NC-n
Hole
P = 10.5
SUP/EXH passage blocked
20.5
Downward
A
16
16
18
Series
31.5
32
35
39
L
3.2
10
D
6
8
(Precautions)
1. The back pressure check valve as-
2. When a back pressure check valve
sembly is the parts with a check
valve structure. However, since the
valve has slight air leakage, take
precautions for the exhaust air not
to be restricted at the exhaust port.
is mounted, the effective area of
the valve will decrease by about
20%.
Applicable
fitting size
5/32"
5/16"
1/8"
1/4"
ø
d
D side
VQ1000
KQ2P-01
KQ2P-03
KQ2P-07
KQ2P-09
Model
EXH block
base assembly U side
n: Stations
Upward
20.5
16
16
18
A
31.5
32
35
39
L
66
8.5
10
D
5
6