VX2110-01T-3CR1 SMC Corporation, VX2110-01T-3CR1 Datasheet - Page 43

• Manufacturer Part Number: VX2110-01T-3CR1
• Description: Process Solenoid Valve, 2 port, direct operated, 1/8 port, NC, 110VAC, conduit
• Manufacturer: SMC Corporation
• Type: Direct Operatedr

Specifications of VX2110-01T-3CR1

• Brand/series: VX Series
• Number Of Ports: 2
• Primary Type: Solenoid Valve
• Size, Port: 1⁄8" NPTF
• Voltage, Coil: 110 VAC
• Enclosure: Equivalent to IP65

1. Leakage voltage
2. Low temperature operation
1. If air leakage increases or equipment does
2. Do not apply external force to the coil section.
3. Be sure not to position the coil downwards.
4. Do not warm the coil assembly with a heat
5. Secure with brackets, except in the case of
6. Avoid sources of vibration, or adjust the arm
7. Painting and coating
Back page 3
Particularly when using a resistor in parallel with a switching
element and using a C-R element (surge voltage suppressor) to
protect the switching element, take note that leakage current
will flow through the resistor, C-R element, etc., creating a
possible danger that the valve may not turn off.
AC/Class B built-in full-wave rectifier coil: 10% or less of rated
voltage
AC/Class B/H coil: 20% or less of rated voltage
DC coil: 2% or less of rated voltage
1. The valve can be used in an ambient temperature of between
2. When using valves for water application in cold climates, take
not operate properly, stop operation.
After mounting is completed, confirm that it has been done
correctly by performing a suitable function test.
When tightening is performed, apply a wrench or other tool to
the outside of the piping connection parts.
When mounting a valve with its coil positioned downwards,
foreign objects in the fluid will adhere to the iron core leading to
a malfunction.
insulator, etc.
Use tape, heaters, etc., for freeze prevention on the piping and
body only. They can cause the coil to burn out.
steel piping and copper fittings.
from the body to the minimum length so that
resonance will not occur.
Warnings or specifications printed or labeled on the product
should not be erased, removed or covered up.
–10 to –20C. However, take measures to prevent freezing or
solidification of impurities, etc.
appropriate countermeasures to prevent the water from
freezing in tubing after cutting the water supply from the pump,
by draining the water, etc. When warming by a heater, etc., be
careful not to expose the coil portion to a heater. Installation of
a dryer, heat retaining of the body is recommended to prevent
a freezing condition in which the dew point temperature is high
and the ambient temperature is low, and the high flow runs.
Warning
Caution
2 Port Solenoid Valve for Fluid Control
Precautions 2
Be sure to read this before handling.
For detailed precautions on each series, refer to the main text.
Switching element
Leakage current
Mounting
Selection
C
OFF
R
Leakage voltage
Valve
5. Connection of piping to products
6. Steam generated in a boiler contains a large
7. In applications such as vacuum and non-leak
1. Preparation before piping
2. Wrapping of pipe tape
3. Avoid connecting ground lines to piping, as
4.Always tighten threads with the proper tight-
Tightening Torque for Piping
When connecting piping to a product, refer to its instruction
manual to avoid mistakes regarding the supply port, etc.
amount of drainage.
Be sure to operate it with a drain trap
installed.
specifications,
against the contamination of foreign matters
or airtightness of the fittings.
Before piping is connected, it should be thoroughly blown out
with air (flushing) or washed to remove chips, cutting oil and
other debris from inside the pipe.
Install piping so that it does not apply pulling, pressing, bending
or other forces on the valve body.
When connecting pipes, fittings, etc., be sure that chips from the
pipe threads and sealing material do not enter the valve.
Furthermore, when pipe tape is used, leave 1.5 to 2 thread
ridges exposed at the end of the threads.
this may cause electric corrosion of the
system.
ening torque.
When attaching fittings to valves, tighten with the proper tighten-
ing torque shown below.
Connection threads
Caution
Rc 1/8
Rc 1/4
Rc 3/8
Rc 1/2
use
Piping
Winding
direction
Proper tightening torque N
caution
Pipe tape
12 to 14
22 to 24
28 to 30
7 to 9
specifically
⋅
m