PIC18F23K22-I/ML Microchip Technology Inc., PIC18F23K22-I/ML Datasheet - Page 237

• Manufacturer Part Number: PIC18F23K22-I/ML
• Description: 8KB, FLASH, 768BYTES-RAM, 8-BIT FAMILY, NANOWATT XLP, 28 QFN 6X6MM TUBE
• Manufacturer: Microchip Technology Inc.

Specifications of PIC18F23K22-I/ML

• A/d Inputs: 17-Channel, 10-Bit
• Comparators: 2
• Cpu Speed: 16 MIPS
• Eeprom Memory: 1K Bytes
• Input Output: 24
• Interface: I2C/SPI/UART/USART
• Memory Type: Flash
• Number Of Bits: 8
• Package Type: 28-pin QFN
• Programmable Memory: 8K Bytes
• Ram Size: 512 Bytes
• Speed: 48 MHz
• Temperature Range: –40 to 125 °C
• Timers: 1-8-bit, 3-16-bit
• Voltage, Range: 1.8-5.5 V
• Lead Free Status / Rohs Status: RoHS Compliant part

15.5.8 GENERAL CALL ADDRESS SUPPORT
The addressing procedure for the I
the first byte after the Start condition usually
determines which device will be the slave addressed
by the master device. The exception is the general call
address which can address all devices. When this
address is used, all devices should, in theory, respond
with an acknowledge.
The general call address is a reserved address in the
I
GCEN bit of the SSPxCON2 register is set, the slave
module will automatically ACK the reception of this
address regardless of the value stored in SSPxADD.
After the slave clocks in an address of all zeros with the
R/W bit clear, an interrupt is generated and slave soft-
ware can read SSPxBUF and respond.
shows a general call reception sequence.
FIGURE 15-24:
15.5.9 SSPx MASK REGISTER
An SSPx Mask (SSPxMSK) register
available in I
held in the SSPxSR register during an address
comparison operation. A zero (‘0’) bit in the SSPxMSK
register has the effect of making the corresponding bit
of the received address a “don’t care”.
This register is reset to all ‘1’s upon any Reset
condition and, therefore, has no effect on standard
SSPx operation until written with a mask value.
The SSPx Mask register is active during:
• 7-bit Address mode: address compare of A<7:1>.
• 10-bit Address mode: address compare of A<7:0>
 2010 Microchip Technology Inc.
2
C protocol, defined as address 0x00. When the
only. The SSPx mask has no effect during the
reception of the first (high) byte of the address.
GCEN (SSPxCON2<7>)
SDAx
SCLx
SSPxIF
BF (SSPxSTAT<0>)
2
C Slave mode as a mask for the value
S
SLAVE MODE GENERAL CALL ADDRESS SEQUENCE
1
2
General Call Address
2
3
C bus is such that
(Register
4
Figure 15-23
5
15-5) is
6
Preliminary
7
R/W =
8
0
ACK
In 10-bit Address mode, the UA bit will not be set on
the reception of the general call address. The slave
will prepare to receive the second byte as data, just as
it would in 7-bit mode.
If the AHEN bit of the SSPxCON3 register is set, just
as with any other address reception, the slave
hardware will stretch the clock after the 8th falling
edge of SCLx. The slave must then set its ACKDT
value and release the clock with communication
progressing as it would normally.
Address is compared to General Call Address
after ACK, set interrupt
9
PIC18(L)F2X/4XK22
D7
1
D6
2
Cleared by software
SSPxBUF is read
Receiving Data
D5
3
D4
4
D3
5
D2
6
D1
7
DS41412D-page 237
D0
8
ACK
9
’1’