DG419CJ+ Maxim Integrated Products, DG419CJ+ Datasheet - Page 6

• Manufacturer Part Number: DG419CJ+
• Description: IC SWITCH SPDT 8DIP
• Manufacturer: Maxim Integrated Products
• Type: Analog Switchr

Specifications of DG419CJ+

• Function: Switch
• Circuit: 1 x SPDT
• On-state Resistance: 35 Ohm
• Voltage Supply Source: Single, Dual Supply
• Voltage - Supply, Single/dual (±): 10 V ~ 30 V, ±4.5 V ~ 20 V
• Operating Temperature: 0°C ~ 70°C
• Mounting Type: Through Hole
• Package / Case: 8-DIP (0.300", 7.62mm)
• Number Of Switches: Dual
• Switch Configuration: SPDT
• On Resistance (max): 35 Ohms
• On Time (max): 175 ns
• Off Time (max): 145 ns
• Off Isolation (typ): 68 dB
• Supply Voltage (max): +/- 20 V
• Supply Voltage (min): +/- 4.5 V
• Supply Current: - 0.0001 uA
• Maximum Power Dissipation: 727 mW
• Maximum Operating Temperature: + 70 C
• Mounting Style: Through Hole
• Description/function: Analog Switch
• Input Level: CMOS, TTL
• Minimum Operating Temperature: 0 C
• Off State Leakage Current (max): 5 nA
• Package: 8PDIP N
• Maximum On Resistance: 100@10.8V Ohm
• Maximum Propagation Delay Bus To Bus: 175@±15V ns
• Maximum High Level Output Current: 30 mA
• Switch Architecture: SPDT
• Power Supply Type: Single|Dual
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

Using supply voltages other than ±15V reduces the
analog signal range. The DG417/DG418/DG419 switch-
es operate with ±4.5V to ±20V bipolar supplies or with
a +10V to +30V single supply; connect V- to 0V when
operating with a single supply. Also, all device types
can operate with unbalanced supplies, such as +24V
and -5V. VL must be connected to +5V to be TTL com-
patible, or to V+ for CMOS-logic level inputs. The
Typical Operating Characteristics graphs show typical
on-resistance with ±20V, ±15V, ±10V, and ±5V sup-
plies. (Switching times increase by a factor of two or
more for operation at ±5V.)
Proper power-supply sequencing is recommended for
all CMOS devices. Do not exceed the absolute maxi-
mum ratings because stresses beyond the listed rat-
ings may cause permanent damage to the devices.
Always sequence V+ on first, followed by VL, V-, and
logic inputs. If power-supply sequencing is not possi-
ble, add two small, external signal diodes in series with
the supply pins for overvoltage protection (Figure 1).
Improved, SPST/SPDT Analog Switches
6
______________________________________________________________Pin Description
__________Applications Information
DG417
_______________________________________________________________________________________
—
—
—
1
2
3
4
5
6
7
8
DG418
PIN
—
—
—
1
2
3
4
5
6
7
8
Operation with Supply Voltages
DG419
—
—
—
2
3
4
5
6
7
1
8
Overvoltage Protection
NAME
GND
N.C.
S1
V+
VL
S2
IN
V-
D
S
S
Other than ±15V
Analog-Switch Source Terminal (normally closed)
Analog-Switch Source Terminal (normally open)
Analog-Switch Source Terminal 1 (normally closed)
No Internal Connection
Logic Ground
Analog-Signal Positive Supply Input
Logic-Level Positive Supply Input
Logic-Level Input
Analog-Signal Negative Supply Input
Analog-Switch Drain Terminal
Analog-Switch Source Terminal 2 (normally open)
Adding diodes reduces the analog signal range to 1V
below V+ and 1V above V-, without affecting low switch
resistance and low leakage characteristics. Device
operation is unchanged, and the difference between
V+ and V- should not exceed +44V.
Figure 1. Overvoltage Protection Using External Blocking Diodes
V
g
FUNCTION
S
V+
V-
DG41_
D