AM28F512-150JC AMD (ADVANCED MICRO DEVICES), AM28F512-150JC Datasheet - Page 8

• Manufacturer Part Number: AM28F512-150JC
• Manufacturer: AMD (ADVANCED MICRO DEVICES)

Specifications of AM28F512-150JC

• Lead Free Status / Rohs Status: Not Compliant

V
voltages). When V
disabled, all internal program/erase circuits are
disabled, and the device resets to the read mode. The
device ignores all writes until V
must ensure that the control pins are in the correct logic
state when V
Write Pulse “Glitch” Protection
Noise pulses of less than 10 ns (typical) on OE#, CE#
or WE# will not initiate a write cycle.
FUNCTIONAL DESCRIPTION
Description of User Modes
Legend:
X = Don’t care, where Don’t Care is either V
Notes:
1. V
2. Manufacturer and device codes may also be accessed via a command register write sequence. Refer to Table 2.
3. 11.5 < V
4. Read operation with V
5. With V
6. Refer to Table 3 for valid D
7. All inputs are Don’t Care unless otherwise stated, where Don’t Care is either V
8. If V
8
Read-Only
Read/Write
CC
levels of V
for the device. Refer to the DC characteristics. When V
addresses except A9 and A0 must be held at V
rise time and fall time specification of 500 ns minimum.
PPL
< V
CC
may be grounded, connected with a resistor to ground, or < V
PP
LKO
ID
1.0 Volt, the voltage difference between V
at high voltage, the standby current is I
PPH
CC
< 13.0 V. Minimum V
(see DC Characteristics section for
. 0 V < An < V
> V
Read
Standby
Output Disable
Auto-select Manufacturer
Code (Note 2)
Auto-select Device Code
(Note 2)
Read
Standby (Note 5)
Output Disable
Write
Operation
CC
LKO
< V
PP
to prevent uninitentional writes.
LKO
= V
Table 1. Am28F512 User Bus Operations (Notes 7 and 8)
IN
CC
, the command register is
PPH
during a write operation.
+ 2 V, (normal TTL or CMOS input levels, where n = 0 or 9).
ID
CC
may access array data or the Auto select codes.
rise time and fall time (between 0 and V
> V
IL
LKO
or V
. The user
IH
CE
IL
CC
.
levels. V
V
#
V
V
V
V
V
V
V
V
PP
IH
IH
IL
IL
IL
IL
IL
IL
IL
(E
+ I
and V
Am28F512
#
PP
PP
)
PPL
(standby).
= V
OE
CC
= V
PPL
#
V
V
V
should not exceed 10.0 Volts. Also, the Am28F512 has a V
V
V
V
V
X
X
Logical Inhibit
Writing is inhibited by holding any one of OE# = V
= V
WE# must be a logical zero while OE# is a logical one.
Power-Up Write Inhibit
Power-up of the device with WE# = CE# = V
OE# = V
edge of WE#. The internal state machine is automat-
ically reset to the read mode on power-up.
IH
IH
IH
IL
IL
IL
IL
(G
PP
, memory contents can be read but not written or erased.
#
CC
IH
) WE
< V
or WE# = V
+2.0 V. V
CC
IH
ID
#
V
V
V
V
V
V
+ 2 V. See DC Characteristics for voltage
X
X
X
IH
IH
IH
IH
IH
IL
(W
voltages) is 500 ns.
will not accept commands on the rising
IL
#
PPH
)
or V
IH
(Note 1)
is the programming voltage specified
V
V
V
V
V
V
V
V
V
IH
V
. To initiate a write cycle CE# and
PPH
PPH
PPH
PPH
PPL
PPL
PPL
PPL
PPL
PP
levels. In the Auto select mode all
V
A0
V
A0
A0
A0
X
X
X
X
IH
IL
(Note 3)
(Note 3)
V
V
A9
A9
A9
A9
X
X
X
X
ID
ID
(Note 4)
(Note 6)
HIGH Z
HIGH Z
HIGH Z
HIGH Z
CODE
CODE
D
(01H)
(25H)
D
IL
IL
D
I/O
OUT
OUT
, CE#
IN
and
PP